A 0.45 m 60° 0.6 m T 0.45 m B 60° 0.6 m The two uniform thin discs shown in the figure rest on a horizontal plane and are connected through frictionless pin-joints at A and B by a rigid light rod which remains horizontal. The mass of disc A is 15 kg. and that of disc B is 25 kg. The static coefficients of friction between the plane and discs A and B are, respectively, (u)= 0.2 and (u)=0.55. I At the instant shown, a counterclockwise moment T = 125 Nm is applied to disc B. You are required to,

A 0.45 m 60° 0.6 m T 0.45 m B 60° 0.6 m The two uniform thin discs shown in the figure rest on a horizontal plane and are connected through frictionless pin-joints at A and B by a rigid light rod which remains horizontal. The mass of disc A is 15 kg. and that of disc B is 25 kg. The static coefficients of friction between the plane and discs A and B are, respectively, (u)= 0.2 and (u)=0.55. I At the instant shown, a counterclockwise moment T = 125 Nm is applied to disc B. You are required to,

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.40P: The 60-lb plank rests on a frictionless roller at A, and the 20-lb triangular support BD. Both...

See similar textbooks

Similar questions

The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
The 60-lb plank rests on a frictionless roller at A, and the 20-lb triangular support BD. Both bodies are homogenous. The coefficients of static friction are 0.4 at B and 0.3 at D. Determine the largest force P that can be applied to the plank without initiating motion.
Find the smallest distance d for which the hook will remain at rest when acted on by the force P. Neglect the weight of the hook, and assume that the vertical wall is frictionless.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
The cone clutch transmits the torque C through a conical friction surface with cone angle . The inner and outer radii of the friction surface are a and b, respectively. The left half of the clutch is keyed to the shaft, and the right half drives a machine (not shown) through a gear attached to its outer rim. Assuming uniform pressure on the friction surface, show that the maximum torque that can be transmitted by the clutch is
Part B and C
Part B please
A uniform slender bar AB with a mass of 20 kg and length of 3.6 m leans on a wall as shown. It is attached to a weightless small roller at end A on a smooth horizontal surface. The coefficient kinetic friction between end B and the wall is 0.25. If the bar is released from rest in the position shown when θ is 30°. Then find, determine the normal force at A. determine the normal force at B. determine the frictional force between end B and the wall.
The solid homogeneous cylinder shown has a mass of 30 kg and is rotating at 1200 rpm clockwise about a fixed horizontal axis through O. The coefficient of kinetic friction between the brake and the cylinder is 0.20. If the tension in the spring when the brake is applied is 100 N, determine the time required for the cylinder to stop rotating. Neglect the thickness of the vertical members. (Draw FBD)
Block 2 of mass 1.30 kg is stacked on top of another Block 1 of mass 8.60 kg on an incline plane of angle 38° with respect to the horizontal. The two blocks are linked by a rope which passes over a pulley at the top of the incline, as shown in the diagram. The coefficient of kinetic friction between all surfaces is 0.45. (g = 9.8m/s2,cos 38° = 0.788, sin 38° = 0.616) a) Draw the free body diagrams of each block, b) Write Newton's second law components for each block, c) What is the acceleration of each block? d) If the coefficient of static friction between all surfaces is 0.3 find the angle 0 the plane must be inclined for sliding to commence. NOTE: Solutions involving the energy will not be accepted. 38.0
A2.3-kg sphere S is being moved in a vertical plane by a robotic arm. When the angle e is 40°, the angular velocity of the arm about a horizontal axis through O is 54 deg/s clockwise and its angular acceleration is 209 deg/s? counterclockwise. In addition, the hydraulic element is being shortened at the constant rate of 480 mm/s. Determine the necessary minimum gripping force Pif the coefficient of static friction between the sphere and the gripping surfaces is 0.44. Compare Pwith the minimum gripping force P; required to hold the sphere in static equilibrium in the 40° position. 0.9 m Answers: P= N Ps=
answer the question