Oil of dynamic viscosity 1.4 × 10-3 lbf-sec/ft2 flows through a 1 in. diameter pipe with a mean velocity of 2 ft/sec. Calculate the pressure drop which occurs over a length of 125 ft of pipe.

Q: Calculate the Reynolds number for the flow of each of the following fluids in a 2-in Schedule 40…

A:

Q: Oil with a specific weight of 10.55 kN/m^3 is flowing from A to B through the special fabricated…

A:

Q: Calculate the pressure drop across a fully open angle valve placed in 5-in Scheduled 40 steel pipe…

A: To find: The pressure drop across a fully open angle valve. Given: The rate of heat transfer Q=847…

Q: Water flows at a rate of 2.4 ft³/s in an old, rusty 7.8-in.-diameter pipe that has a relative…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Carbon dioxide with a dpecifuc weight of 0.114lb/ft3 and a dynamic viscosity of 3.34 x 10^-7lb*s/ft2…

A: Given data: w=0.114 lb/ft3μ=3.34×10-7 lb.s/ft2Q=200 ft3/min=3.333 ft3/s Need to determine the value…

Q: Water (specific gravity, G, is 1.0 and the kinematic viscosity, ν, is 1.14 *10-6 m2 /s) flows…

A:

Q: Glycerin (10°C or 50°F) flows in a 50 mm (or 2 in.) pipeline. The center velocity is 2.4 m/s (or 8…

A: Glycerin at 10oC or 50oCd=50mm or 2 inV=2.4 m/s  or 8 ft/s  centerhL=3m or 10 ft

Q: Problem 1: For the system shown in the diagram below, let 4z = 80 m and L = 185 m of cast iron pipe…

A: To determine:Pipe diameter(D)

Q: Fuel oil is flowing in a 4-in Sch maximum rate for which the flow is laminar. If the oil has a…

A: The head loss in the pipe can be calculated using the formula given below as- hf=32μuLρgd2 where, u…

Q: Determine the total length of a wrought iron pipe (e = 0.000046) with a diameter of 1.5 in which…

A:

Q: Fuel oil (sg=0.94) is being delivered to a furnance at a rate of 60 gal/min through a 1 1/2in…

A:

Q: An oil (SG = 0.9) issues from the pipe in Fig.  atQ = 35 ft3/h. What is the kinematic viscosity of…

A: Given: The value of discharge is Q= 35 ft3/h. The diameter is d= 0.5 in The length is L=6 ft. The…

Q: What diameter is required in a pipe with t=0.2 mm and a length of 2450 m, yes it is desired that…

A: To find : The required diameter in a pipe. Given : The thickness is t=0.2 mm. The discharge is…

Q: Each of the two circular pipes carries water at 65 °C flows at a Reynolds Number of 3.8× 10^4.…

A:

Q: transfers hydraulic oil with a kinematic viscosity of 200 cSt through a 2-in. I.D. hose 100 ft. long…

A:

Q: Calculate the Reynolds number for 20oC water flow in a 1” nominal diameter sanitary pipe at Q=…

A:

Q: Wate flows through a 50 mm The pressure drop across the contraction is based off the smaller…

A: Given:Pipe diameter before contraction, d1=50 mm=0.050 mPipe diameter after contraction, d2=25…

Q: Q: Pressure drop in slug flow-M. A light oil and a gas are flowing upward in a vertical tube of…

A: Given:The inner diameter of the vertical tube  The superficial velocity of light oil The superficial…

Q: The working fluid of the pressure gauge in Fig. 157 is mercury.  Estimate the volumetric flow rate…

A: The Answer is below

Q: 7.10. In the laminar flow of an oil of viscosity 1 Pas the velocity at the center of a 0.3 m pipe is…

A: Given:Viscosity of the oil, μ=1 Pa.sDiameter of the pipe, d=0.3mVelocity at the center, Vmax=4.5 m/s