Wate flows through a 50 mm The pressure drop across the contraction is based off the smaller diameter. Density of water is diameter tube that suddenly contracts to 25 mm diameter tube. 45 kpa Assume the contraction has a loss coefficient (k) of 1000 kg/m^3 Determine the volume flow rate. 0.35

Q: 1. Outcome #3. You must show and explain all work. A speed boat utilizes a jet pump for propulsion.…

A: Given: Thrust force (F) = 130 kN = 130,000 N Inlet area at station 1 (A1) = 0.07 m² Velocity at…

Q: 1. Refer to figure 1: A frictionless ramp inclined at 30.0° has a solid, homogeneous ball that sits…

A: for the given system  angle of ramp () = 30o To determine  Initial potential energy the ball had…

Q: Define the Nonmechanical Forms of Work.

A: In thermodynamics, the non-mechanical work is the work which is determined by the non-contact or the…

Q: The car engine has a torque of 0.4 kNm at 2000 rpm (rev/min). What is the power (kW) at this time?

A: Given data: torque (T) = 0.4 kNm Speed (N) = 2000 rpm Need to determine the power.

Q: Ten and one-half foot-pounds of work is required to compress a spring 2 inches from its natural…

A: Given data  Work = 10+1/2 (lb-ft) Initial compression = 2in  Find the work required to compress the…

Q: Sketch the normal and tangential coordinates and the acceleration vector and on each airplane for…

A: Acceleration is the rate of change of speed per unit time. Speeding up means the airplane has…

Q: If a car weighing 2400 lbs is able to go 1000 ft up a mountain incline whose angle of inclination is…

A: Given data: Weight of car = 2400 lbs                      Distance which car moves up the incline =…

Q: Q1. A conservative force is a force that the work done by it only depends on its initial and final…

A: Conservative force is the force due to which work done arise depends on initial and final positions…

Q: wind velocity on the downstream side of the turbine in m/s

A: To find wind velocity on the downstream side of the turbine in m/s

Q: 2.4.19. [Level 2] A bicyclist comes around a decreasing-radius turn and maintains a constant speed…

A: Bicyclist speed (v) = 20 mph = 20(5280/3600) = 29.33 ft/s[Note: 1 mile = 5280 ft   and  1 hour =…

Q: An saw blade starts from 9 rad/s and accelerates at 4 rad/s2 and covers 483 rad. Determine the time…

A:

Q: In a curvilinear motion, the direction of the instantaneous velocity is always a. Tangent to the…

A: c. Tangent to the path of motionIn a curvilinear motion, the direction of the instantaneous velocity…

Q: -2- A force of 500N acts on a body with a mass of 5 kg. What is the acceleration with which you will…

A:

Q: You want to upgrade the tires on your truck. The manufacturer tires are P160/70R14. You want to…

A: 14 inch is the correct answer.

Q: (1)Changethedistributedload from 400 lb/ft to 550 lb/ft.Keep inmind that this change will result in…

A:

Q: . A for of 40.0 N is required to pull a wooden block at a constant velocity across a smooth glass…

A: Given     Mass, m = 10 kg

Q: You want to upgrade the tires on your truck. The manufacturer tires are P160/70R14. You want to…

A: The old tyre is P 160/70 R14  ie. 160 shows the section width in mm  70 shows aspect ratio  R14 rim…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.