The total volume required to reach the endpoint of a titration required more than the 50 mL total volume of the buret. An initial volume of 49.48± 0.05 mL was delivered, the buret was refilled, and an additional 1.73 + 0.06 mL was delivered before the endpoint was reached. The titration of a blank solution without the analyte required 0.54 ± 0.04 mL. Calculate the endpoint volume corrected for the blank and its absolute uncertainty. Note: Significant figures are graded for this problem. To avoid rounding errors, do not round your answers until the very end of your calculations. volume: mL mL

The total volume required to reach the endpoint of a titration required more than the 50 mL total volume of the buret. An initial volume of 49.48± 0.05 mL was delivered, the buret was refilled, and an additional 1.73 + 0.06 mL was delivered before the endpoint was reached. The titration of a blank solution without the analyte required 0.54 ± 0.04 mL. Calculate the endpoint volume corrected for the blank and its absolute uncertainty. Note: Significant figures are graded for this problem. To avoid rounding errors, do not round your answers until the very end of your calculations. volume: mL mL

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Only typed solution
A piece of Gold weighing 12,359 Kg is suspected of being contaminated with Iron. To perform an instrumental analysis and To confirm whether or not it contains Fe, a portion of the sample (0.954 g) is taken from the piece and dissolved with 25 mL of aqua regia. Heats up For its complete dissolution, it is cooled and made up to 100 mL. A 10 mL aliquot is taken from this solution and made up to 50 mL. From This last solution is given the appropriate treatment to visualize Fe+2, for which the 1,10-phenanthroline reagent is added. (it forms a complex that is red in color) and is taken to a visible spectrophotometer and with a 12 mm cell a absorbance of 0.45. Previously, a calibration curve of Fe+2 was obtained under the same instrumental conditions obtaining the following data: (view table) Calculate the purity of the gold piece, assuming impurities only due to Fe.
Your pH meter was improperly calibrated and reports a pH value consistently lower by 0.002 compared to the correct value. This discrepancy introduces error to your data. systematic random
To determine the pKa of PNP, a student needs to prepare a solution of 42.0 µM PNP in 30.0 mM acetate pH 5.2, with a total volume of 1,000 µL. Stock solutions of 0.200 mM PNP and 90.0 mM acetate pH 5.2 are available. Calculate the volume of dH2O required to make the solution (in µL).
4- A sample containing H2C204 had a purity equal to 90.50% (w/w). An unknown mass of this sample was dissolved in water and transferred to a 50.00 mL flask. An aliquot of 25.00 mL was transferred to an erlenmeyer flask and 50.00 mL of a 0.2000 mol L^-1 NaOH solution were added. %3 Excess NaOH was titrated with 0.09000 mol L^-1 HCI solution using 2.000 mL. Calculate the mass (g) of the sample used. Data: H = 1.008 C= 12.01 O = 16.00
Consider the titration of 27.00 mL of 0.100 M HNO3 with 0.0900 M KOH. Calculate the pH at the following volumes of the titrant: VT = 0.00 VT = 12.50 VT = 17.50 VT = 30.00 VT = 37.50 VT = 42.50
What is the mass of pure dry CaCO3 (MW: 100.0869 g/mol) standard used in the standardization of EDTA solution? Assume that 1.758 M EDTA solution was computed based on the titration of CaCO3 standard. The volume of titrant needed to reach the endpoint was 35.00 mL. Ca2+ + Y4- → CaY2- 0.1500 g 5.630 g 6.158 g 0.6158 g
The calcium content of a milk sample was to be determined by EDTA titration. A sample weighing 0.206 g was mixed with an aqueous buffer at pH 11.5. A few drops of EBT indicator were added and the solution required 24.25 mL of 1.538 x 10-2 M EDTA to reach the endpoint. Calculate the weight percent of calcium (FW =40) in the milk.
If the absorbance for the solution was 0.342, calculate the equilibrium constant, Keq, with zero places after the decimal.
You are titrating 40.040.0 mL of 0.0100 M Sn2+Sn2+ in 1 M HCIHCI with 0.0500 M T13+T|3+ resulting in the formation of Sn4+Sn4+ and Tl+Tl+. A PtPt indicator electrode and a saturated Ag|AGCIAG|AgCl reference electrode are used to monitor the titration. Calculate the cell potential (EE) after each of the given volumes of the TI3+TI3+ titrant have been added. a. 1ml b. 4ml c.7.90ml d.8ml e.8.10ml f.13ml
A 20-mL solution of 0.0659 M AgNO3 was titrated with 20 mL of 0.0509 M NaCl (Ksp = 1.8x10-10). Calculate the pAg of the analyte solution. Express your answer with 3 decimal places.
Calculate the molarity of the nickel solution. From the following data calculate the normalities of the acid and base solutions: weight of pure Na2CO3 = 0.2448 g; volume of acid = 43.65 mL ; volume of base used in back titration = %3D 0.84 mL ; 1.000 mL of base = 0.982 mL of acid. Reaction: CO, + 2H* → H2CO3