In the acetic acid determination in vinegar experiment; NaOH was standardized with 0.25 g KHP (molar mass = 204 22 g/mol). The KHP was dissolved in 50.0 mL distilled water in a 250 mL Erlenmeyer flask and titrated to the endpoint colour by dispensing 6.50 mL of NAOH from the burette. Calculate the molarity of NaOH. O a 0. 19 M O b. 1.9 X 10+M Oc 0.00016 M Od. 0.25 M O e. 0.019 M Clear my choice

In the acetic acid determination in vinegar experiment; NaOH was standardized with 0.25 g KHP (molar mass = 204 22 g/mol). The KHP was dissolved in 50.0 mL distilled water in a 250 mL Erlenmeyer flask and titrated to the endpoint colour by dispensing 6.50 mL of NAOH from the burette. Calculate the molarity of NaOH. O a 0. 19 M O b. 1.9 X 10+M Oc 0.00016 M Od. 0.25 M O e. 0.019 M Clear my choice

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A 370.00 mL solution of 0.00190 M AB5 is added to a 200.00 mL solution of 0.00165 M CD2. What is pQsp for AD5?
Compute the molarity of KMnO4 solution if 1.0092 g of pure FAS required 25.11 mL of KMnO4 solution to reach end point in an acidic medium. An impure sample of FAS weighed 1.2352 g and it required 26.01 mL of KMnO4 solution (use molarity from Q#2) to reach end point in an acidic medium. Compute %Fe in this sample.
250.0 ml of the mineral water sample was precipitated with potassium sodium tetraphenyl bromate: K+ + B(C6H5)4-  KB(C6H5)(s). The precipitate was filtered, washed and dissolved in an organic solvent. An excess of HgY2- was added to the solution: 4 HgY2- + B(C6H5)4- +4H2O  H3BO3 + 4C6H5Hg+ + 4HY3- + OH-. The liberated EDTA was titrated with 0.05581 M Mg 2+ solution, which consumed 29.64 mL. Calculate the potassium concentration [mg/l] in the sample.
What is the mass of pure dry CaCO3 (MW: 100.0869 g/mol) standard used in the standardization of EDTA solution? Assume that 1.758 M EDTA solution was computed based on the titration of CaCO3 standard. The volume of titrant needed to reach the endpoint was 35.00 mL. Ca2+ + Y4- → CaY2- 0.1500 g 5.630 g 6.158 g 0.6158 g
The calcium content of a milk sample was to be determined by EDTA titration. A sample weighing 0.206 g was mixed with an aqueous buffer at pH 11.5. A few drops of EBT indicator were added and the solution required 24.25 mL of 1.538 x 10-2 M EDTA to reach the endpoint. Calculate the weight percent of calcium (FW =40) in the milk.
In the titration of MgSO4.2H2O (2g per litre) against a 0.01 M solution of the disodium salt of ethylenediamine tetraacetic acid (EDTA) the titres obtained were as follows ; titre 1: start - 0.7 ml and end - 13.3 ml (12.6ml) titre 2: start - 13.3 ml and end 25.7 ml (12.4ml) The average titre is 12.5ml Q. Calculate, based on the average titre of the accurate titres, the percentage of magnesium in the magnesium salt
Use the following atomic masses (in g/mol): Mg = 24.31; O = 16; Ca = 40.08; C = 12.01; Na = 23; H = 1; N = 14.01; S = 32.06; Cl = 35.45; A 4.59mL sample of HCl (sp. gr. = 1.3) required 5.5mL of 0.9544N NaOH in titration. Calculate the %w/w of HCl in the sample.
The standardization of same titrant during the determination of BOD5 of water sample was done separately for Day 1 and Day 5. Upon standardization, it turned out that the concentration of the titrant in Day 1 is higher than the concentration of the same batch of titrant in Day 5. How would you explain this discrepancy? (A) There were bubbles at the tip of the burette during titration. (B) Too much starch indicator was added in the conical flask. Sulfuric acid was added first before potassium iodide. (D) The water used to prepare the Na₂S₂O3 solution was not boiled resulting to proliferation of bacteria.
a 20 ml portion of a deep well water sample was diluted to 250 ml solution. a 50 ml aliquot of this diluted sample water was buffered at ph 10 and required 8. 50 ml of a standard EDTA.the titrant was standardized using 100ml containing 0.8622 mg primary standard calcium carbonate , which required 15.45 ml for titration.(a) identify a possible indicator and its endpoint color (b) calculate the molarity of the EDTA solution. (c) calculate the total hardness of the water as ppm CaCO3 (d) identify the quality of the water sample in terms of hardness
A 20-mL solution of 0.0659 M AgNO3 was titrated with 20 mL of 0.0509 M NaCl (Ksp = 1.8x10-10). Calculate the pAg of the analyte solution. Express your answer with 3 decimal places.
Calculate the grams of Ca atoms in 1 mol of CaSO4