The temperatures of the 20 ºC 25 ºC 30 ºC water at outletTask 1 Explain the system parameters using the Non- Flow Energy Equation The given information is summarized in the table below for three different casesGiven ParametersCase ACase BCase CPower delivered by the 20 kW25 kW30 kWelectric motor into thecompressorMass flow rate of the air 0.3 kg0.5 kg1 kgdrawnThe receiver pressure12 bar gauge13 bar gauge15 bar gaugeAtmospherictemperatureThe temperature of the 30 °Cair entering the receiverThe temperature of the 15 °Cair leaving the receiverCooling water flows20 °C23 °C25 °C35 °C40 °C20 °C25 °C0.5 kg0.7 kg1 kgThe temperatures of the 12 °Cwater at inlet13 °C15 °C

Answered: The temperatures of the 20 ºC 25 ºC 30…

The temperatures of the 20 ºC 25 ºC 30 ºC water at outlet Task 1 Explain the system parameters using the Non- Flow Energy Equation

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A standard oil-gas horizontal separator, the gas stream has flow rate around 3.5MMscfd, the amount of oil flow rate 870 bbl./day, the working pressure 1000 psia under temperature 31°C, it's full to a third liquid capacity and the amount of mass flow rate=77161.81b/hr. If the settling size of this separator is (36*10'), assess if it's possible to use this size in well with all these conditions then summarize the final result, calculate the mass velocity in this separator Fraction factor 1.2, compressibility factor 0.86, Gas sizing constant 0.19 Density of liquid and gas (5.2,3.1) lb./cuft respectively.
1. Show complete solution ang illustration.
For the purpose of acting as an air-cooled water chiller, an ammonia refrigerant vapor compression system is deployed. It is functioning with an evaporator temperature of 0 degrees Celsius and a condenser temperature of 40 degrees Celsius. The refrigeration produced by the system is equal to 15 tons.Find out: a. The temperature of the discharge and the mass flow rate of the refrigerant that is being circulated.b. The piston displacement that can be considered theoretical for the compressor.c. The work that can be done by the theoretical compressor.d. The heat that is not allowed to escape through the condenser.e. The Carnot coefficient of performance and the actual COP of the cycle.f. The volume of air that is supplied in the condenser if the air comes in at 30 degrees Celsius and exits at 34 degrees Celsius.g. The LMTD and AMTD of the condenser h. The water flow rate of the chiller assuming that the water enters the evaporator at 10 degrees Celsius and exits at 5 degrees Celsiusi. The…
The return air temperature of the room is 78F and cooling system load is 48,000 Btu h (sensible). How much air flow (in CFM) is required for proving 58F as the supply air temperature?
_is the amount of heat transferred to water to produce the required quantity of steam Quality of steam O Capacity of boiler Quantity of steam Steaming rate
Please as soon as possible
I want a quick solution
Figure below shows a steam jet refrigeration system that produces chilled water in a flash chamber. The chamber is maintained at a pressure by the steam ejector, which removes the vapor generated by entraining it in the low-pressure jet and discharging into the condenser. The vacuum pump removes air and other non-condensable gases from the condenser shell. For the conditions shown on the figure, determine the make-up water and cooling water flow rates in kg/hr. SHOW THE NEEDED DIAGRAMS FOR THE SOLUTION
Please no written by hand solutions A 4-ton heat pump is installed. Desired flow rate is 12 USgpm. The runner and header from the Mechanical room is 110 feet in delivery and 110 feet in return. The fluid running in the system is Methanol-20%. The ground loop consists of three parallel vertical loops each 290 feet in length. The ground loop is made of 0.75" HDPE SDR 11 pipes and the runner-header is made of 1.25" HDPE SDR 11 pipes. The heatpump pressure drop is given 5.8 ft of wc for a flow of 6 gpm of water (Correction factor 20% Propylene Glycol:1.36, 20% Methanol: 1.25, 25% Ethanol: 1.32). Q: Calculate the pressure drop in the Runner-Header. Question 11 options: 9.9 ft of wc 5.8 ft of wc 7.3 ft of wc 3.8 ft of wc 13.4 ft of wc 2.9 ft of wc
From the knowledge you have learned in the simple vapour compression cycle and multi-pressure refrigeration system, For both the diagram apply your knowledge by:a. Draw the PH diagram from the given schematic diagram belowb. Explain in details the concept and principle behind the diagram. This includes the mass of refrigerant flow and distribution.c. Explain in details the analysis behind the diagram.
1. Figure 1 below shows a stirred tank heating process-with a constant holdup volume. Assume mass flow rate w, of the inlet pipe is constant whereas its temperature T fluctuates but the product temperature T must be maintained within set temperature tolerances about the reference. Heater Figure 1: Stirred heating tank process
Complete soln and correct units pls. Thanks