The table shows the tensile stress-strain values obtained for various hypothetical metals. Based on this, indicate which material will be the most ductile and which the most brittle. Material Yield strength Tensile strength Breaking strain Breaking strength Elastic modulus (MPa) (MPa) (MPa) (GPa) A 310 340 0.23 265 210 B 100 120 0.40 105 150 с 415 550 0.15 500 310 D 700 850 0.14 720 210 E - Non-effluence fracture 650 350

The table shows the tensile stress-strain values obtained for various hypothetical metals. Based on this, indicate which material will be the most ductile and which the most brittle. Material Yield strength Tensile strength Breaking strain Breaking strength Elastic modulus (MPa) (MPa) (MPa) (GPa) A 310 340 0.23 265 210 B 100 120 0.40 105 150 с 415 550 0.15 500 310 D 700 850 0.14 720 210 E - Non-effluence fracture 650 350

Chemistry for Engineering Students

3rd Edition

ISBN:9781285199023

Author:Lawrence S. Brown, Tom Holme

Publisher:Lawrence S. Brown, Tom Holme

Chapter1: Introduction To Chemistry

Section: Chapter Questions

Problem 1.82PAE: Use the web to research the elastic modulus and yield strength of carbon fiber composites. How do...

See similar textbooks

Similar questions

Cloth can be waterproofed by coating it with a silicone layer. This is done by exposing the cloth to (CH3)2SiCl2 vapor. The silicon compound reacts with OH groups on the doth to form a waterproofing film (density = 1.0 g/cm3) of [(CH3)2SiO]n, where n is a large integer number. n (CH3)2SiCl2 + 2n OH 2n Cl + n H2O + [(CH3)2SiO]n The coating is added layer by layer, with each layer of [(CH3)2SiO]n being 0.60 nm thick. Suppose you want to waterproof a piece of doth that is 3.00 square meters, and you want 250 layers of waterproofing compound on the cloth. What mass of (CH3)2SiCl2 do you need?
B Consider a two-component alloy with components A and B, with densities of A: 8.2 g/cm³ and B: 12.4 g/cm³. The volume fraction of A is 0.30. What is the weight fraction of A? Select one: a. 0.221 Ob. 0.688 OC 0.342 d. 0.302 e. 0.846 Of 0.112
Glass, quartz, and cristobalite have the same chemical formula, SiO2. Given the XRD diffractograms below, what can you say about each of these compounds? Counts SiO2 Glass 4000 - 2000 Quartz 4000 3000 2000 - 1000 Cristobalite 4000 2000 20 30 40 50 Position [2Theta] (Copper (Cu))
180 Phase Change Diayram 160 140 120 100 60 40 12 14 Time (mintes) 10 16 18 20 22 At point A, the beginning of observations, the substance exists in a solid state. The material in this phase has _6_ volume and_ shape. With each passing minute, substance. This causes the molecules ofthe substance to 10 rise in the substance. At point B, the temperature of the substance is 11°C. The solid begins to_12 8_ is added to the 9_ more rapidly which we detect by a 13 or in a_ 14_ state. The material in this At point C, the substance is completely phase has_15 volume and_16_ shape. The energy put into the substance between minutes 5 and 9 was usedto convert the substance from a_ 17 to a_18. This heat energy is called the latent heat of fusion. Between 9 and 13 minutes, the added energy increases the 19_ of the substance. During the time from point D to point E, the liquid is the 20. By point E, the substance is completely in 22 volume and 23_ shape. phase. The material in this phase has 21 The…
1. What are the principal natural processes that affect the petrophysical properties of sedimentary rocks? 2. As shown in Table 1.1, the total bulk chemical analysis of rock samples is clearly different from the surface analysis. What effect does this have on the rock properties?
Why are covalently bonded materials generally less dense than those that are bonded ionically or methallically?
8. Give an example of a stress concentration in a metal part.
3.108 As chip speeds increase, the width of the interconnects described in Problem 3.107 must be reduced. A hypothetical limit to this process would be reached if the interconnect was just one copper atom wide. Use the density of copper (8.96 g/cm3) to estimate the diameter of a copper atom. (Optical interconnects are being developed, and are likely to replace copper in this application within a few years.)
Metals, polymers, and ceramics form what "new" class of materials? Pick the correct answer: A) Laminates B) Exotics C) ceramics D) Alloys
Two previously undeformed cylindrical specimens of an alloy are to be strain hardened by reducing their cross-sectional areas (while maintaining their circular cross sections). For one specimen, the initial and deformed radii are 17 mm and 11 mm, respectively. The second specimen, with an initial radius of 13 mm, must have the same deformed hardness as the first specimen; compute the second specimen's radius after deformation.
Why do you think polymers have no definite melting point?
State whether the following statement is ‘True’ or ‘False’. (2 × 10 = 20) Give a brief explanation for each of your answers, as applicable. Alpha-Polonium has a body-centered cubic structure. True False A dislocation loop must always be a mixed dislocation. True False Divacancies in any metal are present at much higher concentration than monovacancies. True False Generally, a quenched metal has a higher electrical resistivity than an annealed metal. True False Shockley partials are considered glissile in nature. True False Wider stacking faults make cross-slip more difficult, that is why cross-slip in brass (Cu-Zn) is more difficult than copper (Cu). True False According to Hume-Rothery’s rule, the solvent and solute in a substitutional solid solution must have 5% size difference. Pearson symbol of copper cP2. True False Frank partial is a sessile dislocation. True False Edge dislocations can cross-slip to move to other slip planes. True False