The system in Figure consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long- radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m³/s of water at 20°C into the reservoir? For water at 20°C, take p = 998 kg/m³ and μ = 0.001 kg/m.s. For cast iron, take € = 0.26 mm Elevation 500 m 7 45° 45° Open globe Sharp exit

The system in Figure consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long- radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m³/s of water at 20°C into the reservoir? For water at 20°C, take p = 998 kg/m³ and μ = 0.001 kg/m.s. For cast iron, take € = 0.26 mm Elevation 500 m 7 45° 45° Open globe Sharp exit

Name: Problem #2The system in Figure consists of 1200 m of 5 cm cast iron p
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Problem #2The system in Figure consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevationat point 1 is 400 m, what gage pressure i

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As shown in the following figure, a pipe of cross-sectional area A = 0.01 m2 and atotal length of 5.5 m is used for siphoning water from a tank. The discharge from the siphonis 1.0 m below the level of the water in the tank. At its highest point, the pipe rises 1.5 mabove the level in the tank.(a) What is the water velocity v (m/s) at the discharge? (b) What is the lowest gauge pressure (in bars) in the tube? And wheredoes it occur? Neglect pipe friction. Is the lowest pressure higher than the vapor pressureof water at room temperature?(c) If the siphon reaches virtually all the way to the bottom of the tank (but is notblocked off), is the time taken to drain the tank equal to t = V/Av, where V is the initialvolume of water in the tank, and v is still the velocity (e.g., 4.43 m/s) as computed abovewhen the tank is full? Explain your answer.(d) A siphon can drain the liquid in the tank, which means that the liquid flowsupward at the right-hand side of the tube. It appears to be…
(b) Use Bernoulli's energy balance equation (E = PV + 0.5*mU²), assume volume flow rate remains constant along the pipe such that (Q=UA), and assume that pressure is balanced manometer to perform the following derivations: (i) (ii) (iii) 1- P2 in the pipe (substitute U2 in this step). an expression for P₁ an expression for P₁ P2 in the U-tube manometer. Set the expressions in parts (i) and (ii) equal to one another and derive the flow equation: U₁ = 2 (Pm -1) gh BA - 1
Question is a fluid mechanics
i need the answer quickly
help
Q5
What’s the answer for this please ?
(b) A certain part of cast iron piping of a water distribution involves a parallel section as shown in Figure Q2(b). Both parallel pipes have a diameter of 30 cm, and the flow is fully turbulent. One of the branches (pipe A) is 1500 m long while the other branch (pipe B) is 2500 m long. The flowrate through pipe A is 4 m³/s. If the friction factor of pipe A and pipe B are the same, determine flowrate through pipe B. Assume the water temperature is 15°C and disregard minor losses.
a circular opening of diameter 300 mm impinges on a rigid wall as shown in the figure. Neglect all minor losses and assume the water level in the tank to remain constant. The net horizontal force experienced by the wall is kN. Density of water is 1000 kg/m3. Acceleration due to gravity g= 10 m/s. %3D Stationary rigid wall 6.2 m Jet Circular opening of diameter 300 mm
Water flows from Reservoir A to Reservoir B. The pipe diameter D is 1 m, and the pipe length L is 300 m. H= 16 m, h = 2 m, and the pipe head loss is given by h₁ = 0.01), where U is the velocity in the pipe. In your solutions consider the head loss at the pipe outlet to be ( U² 2g (a) what is the discharge in the pipe? (b) What is the pressure at point P halfway between the two reservoirs? (c) sketch the HGL and EGL. Water D H P B
Tank 1 Tank 2 g Question 1 Consider the flow of water (p= 10³ kg/m³, u = 10³ Pa-s) from tank 1 to tank 2. A centrifugal pump is installed in this piping system with length L = 300 m and diameter D = 40 cm cast-iron pipe. The water surface of tank 1 is 15 m higher than the water surface of tank 2. You may neglect minor losses but not major losses. The gravity cannot be neglected. Assume steady-state and no friction in the tanks. (a) Simplify the equation of the system curve Ap vs Q. Do not place numerical data. (b) Plot the system curve Ap vs Q (0 ≤Q≤2 m³/s). (c) Find the volumetric flow rate when the pump is not operating. (d) Find the power supplied to the water and to the pump if n = 0.9 and 1 m³/s. (e) Consider a pump: Ap = 106 105 Q², where Ap in Pa and Q in m³/s. Find the operating point. What is the minimum and maximum volumetric flow rate that this pump can deliver?
Find the maximum power developed by the turbine. Data H1= 37 m, H4= 2 1 m, D2=56 cm, D4= 35 cm, V4= 8.5 m/s, P4= 200 kPa, Patm= 100 kPa, 1000 kg/m3. * Lake H, P.O V. h D2 H. Turbine Your answer