The surface finish specification in a turning job is 0.90 um. The work material is cast iron. The cutting conditions have been selected as follows: v = 90 m/min, f 3D0.23mm/rev, and d = 2.2 mm. The nose radius of the cutting tool must be selected. Determine the minimum nose radius that will obtain the specified finish in this operation.

The surface finish specification in a turning job is 0.90 um. The work material is cast iron. The cutting conditions have been selected as follows: v = 90 m/min, f 3D0.23mm/rev, and d = 2.2 mm. The nose radius of the cutting tool must be selected. Determine the minimum nose radius that will obtain the specified finish in this operation.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.10A O50 mild steel bar is being turned at 1.70 revis on a multi-tool center lathe having nine tools. For all tools the depth of cut is 4mm. the feed is 0.255mm/rev, and the specific cutting pressure is 1 545N mm?. Calculate the total power consumed for the operation
A Ø1.0” piece of titanium needs to be turned on a lathe using a carbide cutting tool. The surface speed is 170 ft/min and the chip load is .015 in/rev. What is the recommended feed for the turning operation above?
Determine the metal removal rate of a drilling process using 25 mm diameter twist drill, a cutting speed of 50 m/min and a feed of 0.2 mm/rev. Available drilling machine spindle rpm are: 300, 400, 500, 625, 750, 800, 900, 1000.
Calculate the time required for completing a 5mm deep finishing cut on a 150mm wide, 600mmlong face of a 25mm thick steel block using a face milling cutter of 150mm diameter with 6teeth. The cutting condition are Vc =1.5m/sec and fz = 0.1mm.
A Ø2.0" piece of alloy steel needs to be turned in a lathe using a carbide cutting tool. The surface speed is 425 ft/min and the chip load is .008 in/rev. What is the recommended feed for the turning operation above? O .008 in/rev O .008 in/min O 6.8 in/rev O 425 in/min O 6.8 in/min
The outline of the part in the Figure below is to be profile milled using a 20- mm diameter end mill with two teeth. The part is 10 mm thick. The cutting speed = 125 m/min and feed = 0.10 mm/tooth. The part is also to be drilled with a drill size of 10 mm corresponds to T01 with a cutting speed =75 mm/min and feed = 0.08 mm/rev. The two holes pass completely through the part. 30 rad. 125.75 10 dia., 2 holes Write the part program (G & M code program) for the required machining processes. Use absolute programming with the lower left 25 corner of the part as the origin in the x-y axis system. 150 (All dimensions are in mm.) 25 50 75 35 deg.
Q.4 A single point cutting tool designated as follows 8-14-6-6-6-20-1 is used to machine a work with feed rate of 1mm/rev. Then the maximum height of roughness and average roughness, in mm, are respectively -3 A 0.0350, 8.76×10 B 8.76x10, -3 0.0350 C 0.10123, 0.0253 D 0.0253, 0.10123
Using slot milling with a cutting tool surface width of 36mm was performed from the top surface to cut a workpiece of 85 x 42 x 8 cm into two equal parts. The milling cutter is 180 mm in diameter and has eight teeth. Cutting speed = 60 m/min, chip load = 0.35 mm/ tooth, and depth of cut = 2 mm, given that the setup and machine settings provide an approach distance of 7mm before actual cutting begins and an overtravel distance of 20 mm after actual cutting has finished, and the return time is a 4-second for idle pass stroke. Determine:- 1. What is the total machining time required for the entire workpiece? 2. The maximum metal removal rate during cutting.
In a turning operation on cast iron, the nose radius onthe tool = 1.5 mm, feed = 0.22 mm/rev, and speed = 1.8m/s. Compute an estimate of the surface roughness forthis cut.
The part in Figure 1 is to be drilled on a turret-type drill press. The part is 15.0 mm thick. Threedrill sizes will be used: 8 mm, 10 mm, and 12 mm, which are to be specified in the part programby tool turret positions TO1, T02, and T03. All tooling is high speed steel. Cutting speed = 75mm/min and feed = 0.08 mm/rev. Use the lower-left corner of the part as the origin in the x-y axissystem. Write the part program in the word address format using absolute positioning.
We need to obtain the following part by OD operation in turning, starting from a 100mm diameter cylinder. The maximum allowable depth of cut is 3mm. It is required to make a finishing pass with d=1mm and a feed of 0.3mm/revolution. 150 mm 150 mm The machine has a total power of 10hp and 85% efficiency. The material has a specific energy 500 based on of 25 W/(cm³/min). It is recommended to make the operation at a constant rpm = calculations made for an average diameter. Determine the minimum required time to finish the part. Hint: calculate the maximum material removal rate then the cutting speed for each pass, then the feed rate for each pass and finally the time of cutting. 80 mm 100 mm
In a turning operation on low carbon steel with hardness = 135 HB, the cutting speed = 180 m/min, feed = 0.35 mm/rev, and depth of cut = 6.5 mm. The original work piece has 26 mm Diameter and 120 mm Length. How much power will the lathe draw in performing this operation if its mechanical efficiency = 90% and operator's efficiency = 82%? The specific energy is 3.8 J/mm³