The supporting wheel on a scaffold is held in place on the leg using a 4-mm-diameter pin as shown. (Figure 1) Figure THE 1 of 1 If the wheel is subjected to a normal force of P = 3.3 kN, determine the average shear stress developed in the pin. Neglect friction between the inner scaffold puller leg and the tube used on the wheel. Express your answer to three significant figures and include the appropriate units. Tavg= 65.652 Submit μA Provide Feedback N mm² Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining

The supporting wheel on a scaffold is held in place on the leg using a 4-mm-diameter pin as shown. (Figure 1) Figure THE 1 of 1 If the wheel is subjected to a normal force of P = 3.3 kN, determine the average shear stress developed in the pin. Neglect friction between the inner scaffold puller leg and the tube used on the wheel. Express your answer to three significant figures and include the appropriate units. Tavg= 65.652 Submit μA Provide Feedback N mm² Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

12
8.1 Please help ASAP. Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you.
The 200 x 200 x 1,250-mm oak [E-12 GPa] block (2) shown is reinforced by bolting two 5 x 200 x 1,250 mm steel [E - 200 GPa] plates (1) to opposite sides of the block. A concentrated load of 300 kN is applied to a rigid cap. Assume P-300 kN, L-1.25 m. Determine (a) the normal stresses in the steel plates (1) and the oak block (2). (b) the shortening of the block when the load is applied. B (1) Answers: A₁- A₂- i Part 2 Calculate the cross-sectional area of each steel plate, A₁, and the cross-sectional area of the oak block, Az. i Save for Later P CL (2) C Answer: F₂/F₁- CL Save for Later CL (1) mm² mm² Derive a compatibility equation using force-deformation relationships substituted into a geometry-of-deformation relationship. Express the compatibility equation here as the ratio of the force in the oak block, F₂, to the force in each steel plate, F₁. Attempts: 0 of 1 used Submit Answer Attempts: 0 of 1 used Submit Answer
Please help me answer this problem ASAP badly needed. Thank you
PLEASE DRAW THE FBD!!! DRAW THE FBD
solve both parts
Indicate your assumptions, write the given and make an organized solution.
A clamp coupling is to transmit a power of 13 kW to a shaft rotating at a speed of 511 rpm. Calculate the diameter of the shaft if the allowable shear stress on the shaft is 45 MPa. The number of bolts connecting the two halves is six. The permissible tensile stress for the bolts is 76 MPa. The coefficient of friction between the coupling and the shaft surface may be taken as 0.3. Also, find the diameter of the bolt. Torque in Nm Diameter of shaft in mm Diameter of bolt in mm
The bell-crank mechanism is in equilibrium for an applied load of P = 47 kN. Assume that a = 300 mm, b = 225 mm, and 0 = 57°. The pin at B has a diameter of d = 14 mm, and the bell crank has a thickness of t = 8 mm. Calculate the bearing stress in the bell crank at pin B. (1) P Answer: Bell crank A O= i 34.21 a с MPa B Support bracket b F₁ IF B
Please solve all part's correctly
STATICS OF RIGID BODIES RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS. ANSWER IN 4 DECIMAL PLACES. PS: THE TOLERANCE IS 1 IN THE 3RD SIGNIFICANT DIGIT