The stress-strain diagram of a reinforcement steel having a cross-sectional diameter of 12 mm ameter and 100 mm gage length is determined after its tensile strength test as follows. Based on the stress- ain diagram determine the followings properties of the material (Poisson's ratio of the material is 0.32) :

The stress-strain diagram of a reinforcement steel having a cross-sectional diameter of 12 mm ameter and 100 mm gage length is determined after its tensile strength test as follows. Based on the stress- ain diagram determine the followings properties of the material (Poisson's ratio of the material is 0.32) :

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cylindrical specimen of 1018 steel having a diameter of 6.35 mm and a gauge length of38.1 mm is pulled in tension. Use the load-elongation characteristics tabulated below. Determine the yield strength (σy) at a strain offset of 0.002.
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm. The cross-sectional dimensions of the beam are b1 = 32 mm, d1 = 117 mm, b2 = 19 mm, d2 = 19 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 13 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a M | A В
A steel specimen is tested in tension. The specimen is 25 mm wide by 12.5 mm thick in the test region. By monitoring the load dial of the testing machine, it was found that the specimen yielded at a load of 160 kN and fractured at 214 kN. a. Determine the tensile stress at yield and at fracture. b. If the original gauge length was 100 mm, estimate the gauge length when the specimen is stressed to 1/2 the yield stress.
X Your answer is incorrect. An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 760 mm. The cross-sectional dimensions of the beam are bị = 33 mm, di = 102 mm, bz = 20 mm, d2 = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 10 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 d2 A В b1 Answer: M = 457.082 N-m Save for Later Attempts: 2 of 3 used Submit Answer Usine mutinle attemnts has imnacted vour score
PROBLEMS 203. During a stress-strain test, the unit deformation at a stress of 5000 psi Wap ODserved to be 0.000167 in./in. and at a stress of 20,000 psi it was 0.000667 in./in. If the proportional limit is 30,000 psi, what is the modulus of elasticity? What is the stress corresponding to a strain of 0.0002 in./in.? Would these re- sults be valid if the proportional limit were 18,000 psi? Explain. E = 30 X 106 psi; S 6000 psi %3D Ans. 204. A uniform bar of length L, cross-sectional area A, and weight W is sus- WL If pended vertically from one end. Show that its total elongation is & = 2AE wL? its weight per unit volume is w, show also that & 2E A steel rod having a cross-sectional area of sq in. and a length of 600 ft is suspended vertically. It supports a load of 5000 lb at the lower end. If steel 30 X 106 psi, find the total elongation in the rod. Ans. 8 = 2.64 in. 205 weighs 490 lb/cu ft and E Hint: Use the result of Prob. 204. steel wire 30 ft long, hanging vertically, supports a…
A beam of the cross section shown is made of a steel that is assumed to be elastoplastic with E=29×106psi and σY= 42 ksi. A bending couple is applied to the beam about the z axis, causing plasticzones 2 in. thick to develop at the top and bottom of the beam. After the couple has been removed, determine (a) the residual stress at y=2 in., (b) the points where the residual stress is zero, (c) the radius of curvature corresponding to the permanent deformation of the beam.
Your answer is incorrect. An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm. The cross-sectional dimensions of the beam areb1 = 35 mm, d1= 115 mm, b2= 21 mm, d2 = 21 mm, and a =7 mm. For this material, the allowable tensile bending stress is 15 MPa, and the allowable compressive bending stress is 14 MPa. Determine the largest moment M that can be %3D %3D %3D %3D %3D %3D applied as shown to the beam. b2 a 不 d2 d1 b1 Answer: N-m M% =
A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for high cycle fatigue, o, x N = C, (where the stress amplitude is in MPa). Ignore the geometric detail and assume that Marin's modifying factors are all equal to 1. You are given the minimum stress ain = -213 MPa, the maximum stress omax = 213 MPa. The material data are Tensile strength oUTS = 539 MPa, Basquin's constant c, = 875 MPa, Basquin's exponent a = 0.085. a) Calculate the stress ratio R, the stress amplitude o, in MPa and the mean stress am in MPa. The answers are acceptable with a tolerance of 0.01 for R and of 1 MPa the stresses. R: MPa MPа b) Calculate the corresponding life, in 10° cycles, (tolerance of 0.1 106 cycles) N :
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 680 mm. The cross-sectional dimensions of the beam are b1 = 33 mm, d1 = 93 mm, b2 = 20 mm, d2 = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 16 MPa, and the allowable compressive bending stress is 9 MPa. Determine the %3D largest moment M that can be applied as shown to the beam. b2 M d2 d1 | A B L b1 Answer: M = i N•m
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 580 mm. The cross-sectional dimensions of the beam are b1 = 33 mm, d1 = 112 mm, b2 = 20 mm, d2 = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 15 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a a M d2 A B bị
3-3. Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear between the origin and the first point. Plot the diagram, and determine approximately the modulus of toughness. The rupture stress is or = 53.4 ksi.