The steel rod shown below is 2inches in diameter and is subjected to an eccentric 2000 lb load together with a 1000 in.lb torque. Calculate: a. The induced normal stress at point A due to the 2000 lb force. b. The induced shear stress at point A due to the imposed torque. c. The principal normal and shear stresses

The steel rod shown below is 2inches in diameter and is subjected to an eccentric 2000 lb load together with a 1000 in.lb torque. Calculate: a. The induced normal stress at point A due to the 2000 lb force. b. The induced shear stress at point A due to the imposed torque. c. The principal normal and shear stresses

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pin connection, like that shown in Figure -16, is subjected to a force of 16,5 kN. Determine the shear stress in the 12.0 mm diameter pin.
The hollow rod shown below is 2.99 meters long and is subjected to a torque of 988 Nm at end B. The diameter of the rod is 30 mm and has a wall thickness of 5 mm. The shear modulus of the material is 80 GPa, calculate the angle of twist in radians at B. TNm B meters
Find the Normal Stress at points A, B, and C in the Rod below. Dimensions given are diameters.
Question: Find schematically the normal and shear stresses in the plane when the element in the plane stress state is rotated 30 degrees counterclockwise with the Mohr circle.
A shaft of diameter d is guided in rotation at A (bearing 1) and C (bearing 2) and carries two wheels supporting the indicated loads, The radius of wheel B is 200 mm, and of wheel D is 100mm. The shaft is made of steel. F2 = 6000 N. Dimensions are in mm. Calculate the diameter (mm) of the shaft considering an allowable stress of 270 MPa for a stress composed of bending and torsion.
For the flat stress state shown in the figure. Use Mohr's circle to determine (show the procedure only with the use of geometry): a. Draw Mohr's circle indicating coordinates of the points that represent the given stress state, center, radius, coordinates of the points that represent the state the maximum and minimum normal stresses, coordinates of the maximum shear and angle of rotation from the stress given to the plane principal. b. Use the results of literal a to draw the element subjected to main forces and the element subjected to maximum shear. 12 MPa 19 MPа y 19 MPа 46 MPа 46 MPа 19 MPа 19 MPа 12 MPa
B4 The short concrete cylinder having a diameter of 50 mm is subjected to a torque of 500 Nm and an axial tensile force of 2 kN. Find: 500 Nm 500 Nm A 2kN 2kN (a) the tensile stress in the concrete;
The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid 1.86-in.-diameter steel [G=11400 ksi] shafts with lengths of L₁ = 79 in. and L₂ = 105 in., respectively. Assume Ng-27 teeth and N-42 teeth. The bearings shown permit free rotation of the shafts. (a) Determine the maximum shear stresses T₁, T2 produced in shafts (1) and (2). (b) Determine the rotation angle DA of gear D with respect to flange A. Answers: (a) T₁ = (b) P DIA Nc WWAMACOM Save for Later C 9.3808 = i 2.1378 e Textbook and Media NB L₁ B D TD ksi, 1₂: = i 14.5924 ksi. Attempts: 1 of 5 used Submit Answer
1. A cold drawn mild steel, AISI 1018CD is used to fabricate the hollow shaft as shown in Figure Q1. Torque of 15 Nm and 30 Nm are exerted at B and C, respectively. The outer diameter of the shaft is D = 20 mm and the inner diameter is d = 15 mm. If the modulus of rigidity for the steel used is given as G = 78 GPa, determine: a) the maximum and minimum shear stresses at sections a-a and b-b. b) the angle of twist at end C. 0.3 m A a; B 15 Nm 0.8 m b. b: Figure Q1 с D 30 Nm
Question 3 The A hollow shaft with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P-75kN and torque TB 16 kN.m and TC = 7 kN.m which act in the directions shown in figure Q3. This shaft is made of a material that has a yield stress of yield = 40MPa. Determine the principal stresses and the maximum shear stress acting at point H on the surface of the shaft and factor of safety. Figure Q3 Tc
Assemble a pair of parts A and B with serrated teeth as shown in the figure on the right.A compressive load of 24 kN is acting on the combined structure.The compressive load is transmitted by the three meshing teethTo. Shear stress and compressive stress (contact) generated in the tooth at this timeFind each tactile stress.
For the sets of given stresses on an element given in Table 4–2, draw a complete Mohr’s circle, find the principal stresses and the maximum shear stress, and draw the principal stress element and the maximum shear stress element. Any stress components not shown are assumed to be zero. Work problem #4 4) Sigma_X= -80 ksi, Signma_Y= 40 ksi, Tau_XY= -30 ksi