The steel rod is supported by an aluminum plate of 8 mm thickness. Force P pulls down the rod through the 12 mm hole in the aluminum plate. Neglect all weights of the rod and plate, and based on the design criteria that the maximum allowable shear stress in aluminum to be 70 MPa, calculate the allowable value of P in kN. Round to the nearest tenth. 10 mm T 12 mm - -40 mm- P 8 mm

The steel rod is supported by an aluminum plate of 8 mm thickness. Force P pulls down the rod through the 12 mm hole in the aluminum plate. Neglect all weights of the rod and plate, and based on the design criteria that the maximum allowable shear stress in aluminum to be 70 MPa, calculate the allowable value of P in kN. Round to the nearest tenth. 10 mm T 12 mm - -40 mm- P 8 mm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Refer attached figure of an axial reluctance force actuator on Image 1. While ignoring core reluctances, find the reluctance force, F, if x = 0.004 m and I = 5 A using the atached force expression on attached image 2.
Consider the magnetic circuit given in below figure with parameters: u=153 Ho, d1=9 cm, d236.2 cm, d3=7.9 cm, da=0.3 cm and N=497. Assume that all branches have the same cross-sectional area of 5 cm. Magnetic flux density is 0.1 Wb/m2 in the air gap. Based on the given configuration calculate the current I in [A] in the coil. d2 d3 d, Tolerance + 0.1 relative
Which of the following is not an approved grounding method?A)Metallic underground water pipingB)Ground rodsC)Gas pipingD)Metal frame of a building
A magnetic core in the form of a closed circular ring has a mean length of 30 cm and a cross sectional area of 1 sq cm. Determine the reluctance if the relative permeability of iron is 2400
Solve all parts.
Good and organised Ans result up vote
4- Which of these are types of normal stresses? a. Tensile and compressive stresses b. Tensile and thermal stresses c. Shear and bending 5- If a material has identical properties in all directions, it is called a. Elastic b. Plastic c. Isotropic d. Homogeneous 6- When a wire is stretched to double in length, the longitudinal strain produced in it is a. 0.5 b. 1.0 c. 1.5 d. 2.0
. Plastics are commonly used for (insulating). ) Cover Sheathing Observe . The core is (coated) with crystal. Covered with D Act D Behaves -. A coil is a wire conductor (winded ) in to a spiral shape. O Move ) Through O Coiled
the depth of the solid core is 5 cm. Assume that the relative permeability of the core is 1000 and remains constant and that the current in the coll is 4 A. ignore the fringing effects at the air gap and find the following
A P KN Refer to the figure. d₁ 0.9 m Force P is 60 kN and each force Q is 125 kN. Q KN B Add your answer Integer, decimal, or E notation allowed Q KN The diameter d₁ = 30 mm and diameter d₂ = 50 mm. d₂ 1.2 m What is the normal stress in rod BC in MPa? Round to the nearest integer and enter the magnitude only. C
A ten-turn solenoid has a ferromagnetic core with a relative permeability of 10,000. The length of the solenoid is l=10 cm and its cross section area is A=1 cm2. The amount of current driving the solenoid is 0.1 A. Determine the magnetic flux intensity H in the core. Provide your answer in A/m. Round off to your answer to one decimal.
Which of the following can be the unit of reactive power? a. Mega Volt Ampere b. Mega Watt Reactive c. Mega Watt d. Volt Ampere Reactive