The steel (E = 200GPa, v=0.32) vertical post is loaded to the forces as shown in Figure Q1.If the strain gauges a and b are firmly attached at point A give readings of &a=300μ and =175μ. Determine the magnitudes of P, assuming that P = P2. There is no transverse forceoccurs at point 4. Solve the following problems:(a)Sketch the free body diagram at point 4,(b)Find the moment of inertia of the cross section,(c)Find the normal strains at point A, and(d)Find force P₁.P₂AC2.5 cm60 cmCFigure Q110 cm2.5 cmSection c-c5cm

Answered: Image /qna-images/answer/7bfd7ac0-c5eb-49f6-8837-96de6c3582d3.jpg

The steel (E = 200GPa, v=0.32) vertical post is loaded to the forces as shown in Figure Q1. If the strain gauges a and b are firmly attached at point A give readings of & - 300μ and = 175μ. Determine the magnitudes of P, assuming that P = P2. There is no transverse force occurs at point A. Solve the following problems: (a) Sketch the free body diagram at point A, (b) Find the moment of inertia of the cross section, (c) Find the normal strains at point A, and (d) Find force P₁. 60 cm 2.5 cm 10 cm 2.5 cm Section e-c 5 cm

The steel (E = 200GPa, v=0.32) vertical post is loaded to the forces as shown in Figure Q1. If the strain gauges a and b are firmly attached at point A give readings of & - 300μ and = 175μ. Determine the magnitudes of P, assuming that P = P2. There is no transverse force occurs at point A. Solve the following problems: (a) Sketch the free body diagram at point A, (b) Find the moment of inertia of the cross section, (c) Find the normal strains at point A, and (d) Find force P₁. 60 cm 2.5 cm 10 cm 2.5 cm Section e-c 5 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5:55 PM ~ 3 m 20 kN [Ε B -2 m--2 m--2 m--2 m--2 m--2 m- Member AB is a: N D 30 kN 40 kN O Tensile Member O Compressive Member O Zero-Force Member O Not a Member ( 50 ) l اس. © 2 F G
The state of strain at the point on the arm in Figure Q10 has components ϵx = 200.5 micro-strain, ϵy = 324.4 micro-strain, and γxy = 220.6 micro-strain (1 micro-strain = strain×10-6). Figure 10 Calculate the maximum principal strain. Express your answer in micro-strains. Report your answer to 1 decimal place.
A differential element on the bracket is subjected to plane strain that has the following components: , Ex = 300 x 10-6, Ey = 200 x 10-6, Exy = -500 x 10-6. Use the strain-transformation equations and determine the normal strain Ex' in the x' direction on an element oriented at an angle of 60°. Note, a positive angle is counter clockwise.
A material is subjected to the following strain system,ex=200x10-6, ey=-56x10-6,yxy=230x10-6. Using graphical method, determine A. The principal strains B. The directions of principal strain axes C. The linear strain on an axis inclined at 50o counter clockwise to the direction of ex Given that young's modulus for the material is 207GN/m2 and the poisson's ratio is 0.27, determine the principal stresses
F2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum elongation of the bar and the maximum normal stress. A F1 A. GIVEN: F2 = 100 kN, (1 = 240 cm, €2= 160 cm, bi = 5 cm, bz=10 cm, h=5 cm, E=2.107 N/em², a=20 cm Note: neglect stress concentration. h bị b2 A-A section
The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load P is applied. joint B moves to the coordinate position (0.40 in., -0.55 in.). Assume a - 10 ft, b-7 ft, and h-8 ft. Determine the normal strain in each bar. Answers: EAB Egc i i B P b με με
A force P and a force Q, applied via a nut, are acting on the arm attached to the end of a shaft made of steel. The strain gauge readings on point A of the shaft show the following deformation values: ε1 = 630x10-6, ε2 = 600x10-6, and ε3 = - 189x10-6. Determine the magnitudes of the applied forces P and Q (E = 200 GPa, υ = 0.3).
A force P of 70 N is applied by a rider to thefront hand brake of a bicycle (P is the resultant of anevenly distributed pressure). As the hand brake pivots atA, a tension T develops in the 460-mm long brake cable(Ae = 1.075 mm2 ), which elongates by δ = 0.214 mm.Find the normal stress d and strain in the brake cable.
A tri-axial state of stress, σx , σy, and σz ,exists in a steel machine part. For steel, E = 200GPa and ν = 0.3. Determine the normal strain in the x-direction if σx = 100MPa, σy = 35MPa, σz = 70MPa. Determine the dilatation. Determine the modulus of rigidity.
5 decimal places Determine the total strain (mm/mm) of a 2.64-m bar with a diameter of 21 mm subjected to a tensile force of 71 kN at a temperature increase of 49 C°. Consider the α=27.3 µm/mC° and E = 122 GPa.
The strain components Ex, Ey, and Yxy are given for a point in a body subjected to plane strain. Using Mohr's circle, determine the principal strains, the maximum in-plane shear strain, and the absolute maximum shear strain at the point. Show the angle 0p, the principal strain deformations, and the maximum in-plane shear strain distortion in a sketch. Ex = 0 μE, Ey = 310 με, Yxy = 280 μrad. Enter the angle such that -45° ≤ 0,≤ +45° Answer: Ep1 = Ep2 = Ymax in-plane = Yabsolute max. = 0p = με με urad urad
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression vy/3E where y = 2.3 lb/in.³ is the specific weight of the material, y = 0.8 in. is the distance from the free (i.e., bottom) end of the bar, L = 8 in. is the length of the bar, and E = 23000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar. (c) the maximum normal strain in the bar.