Brake cable, L= 460 mm Hand brake pivot A 37.5 mm P (Resultant of distributed pressure) 50 mm - Uniform hand brake pressure 100 mm

Q: F is being held by two cables AB and CB. If the applied force P creates a displacement at point E…

A: Given: The displacement of point E=3mm Horizontal distance of point E from hinge point F: →d=3+4=7 m…

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

A:

Q: A bar BD is held in a horizontal position when there is no load by the steel wire AB. When a weight…

A: The cross sectional area of wire is The modulus of elasticity is The yield strength is The…

Q: Please solve it ASAP I'll rate The 6-m boom AB is acted upon by the 1.2kN force as shown in figure.…

A:

Q: The state of strain on an element has components Px = -300(10-6), Py = 100(10-6), gxy = 150(10-6).…

A: Given Data: The x component of the normal strain is: εx=-300 X 10-6. The x component of the normal…

Q: Since the suspended mass is m=1500 kg as shown below; Find the force (F) N and the stress N/mm2 in…

A:

Q: Find the forces in all the members of the truss shown in the figure. If all the members have the…

A: Given:The cross-sectional area of each member is The modulus of elasticity of each member is

Q: Two hard rubber blocks [G = 367 kPa] are used in an antivibration mount to support a small machine,…

A: Given Data  LOad =948 N a=20 mm  b=50 mm c=80 mm Two shearing surface SHear area =2bc=2(20)(50)=2000

Q: The state of a plane strain at a point has the components Ex 400 (10-6), ɛy = 200 (10 ) and yxy =…

A:

Q: For the state of a plane strain with εx, εy and γxy components: (a) construct Mohr’s circle and (b)…

A: Given state of a plane strain is-To find:(a) Construct Mohr’s circle and(b) The equivalent in-plane…

Q: New Tab 15MDlxNzMz/a/NDCONZAWMTQYMTK3/details Open wi 3. A rigid member CBD is supported by a…

A:

Q: Consider the given loading on a pipe. A rectangular rosette (45 degree apart) is placed on a point…

A:

Q: At the nodes in the truss system given in the figure occurring displacement and the stress and…

A:

Q: The Strain along the length direction of the block subjected to 3 mutually perpendicular forces as…

A: Given , Px is positive , Py and Pz are negative

Q: Two bars are used to support a load P. When unloaded, AB is 5 in. long, AC is 8 in long ond the A…

A: Given:Length of AB=5 inchlength of AC=8 inchinitial coordinates=0,0Final coordinates=0.25 in, -0.73…

Q: The strain at a point is 780x10-s in the x, 400x10-6 in the y and -500x106 in the z direction.…

A:

Q: The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P…

A:

Q: The cantilevered rack is used to support each end of a smooth pipe that has a total weight of 460…

A: The weight of pipe is W=460 lb

Q: Q2 / The 60° strain rosette are mounted on articular cartilage element. Figure Q2 shows the readings…

A: Consider the diagram shown below for the strain rosette. The general equation for the strain in a…

Q: Find the forces in all the members of the truss shown in the figure. If all the members have the…

A: Given:The cross-sectional area of each member is The modulus of elasticity of each member is

Q: The state of a plane strain at a point has the components &, = -100 (10-5), &y = -50 (10-5) and yw =…

A:

Q: The two bars shown in the figure are used to support a load P. When unloaded, joint B has…

A:

Q: The man has a mass of 84 kg and stands motionless at the end of the diving board. Figure -1.5 m B…

A:

Q: The steel (E = 200GPa, v=0.32) vertical post is loaded to the forces as shown in Figure Q1. If the…

A:

Q: A three strain gages have been attached directly to a piston used to raise a medical chair, the…

A:

Q: Find the strain if stress is 30 MPa and E=100 Mpa

A:

Q: F1, F2 and F3 static forces act on the element shown in the figure. F3 AB (distance b) is in the…

A: Given data, Applied forces are F1 = 3000 N F2 = 5000d N F3 = 2000 N Distances are a = 50 mm b = 900…

Q: The state of plane strain on an element has components € =-410(10-6), ey = 0, and %3D Yæy =…

A:

Q: The piece of plastic is originally rectangular. Suppose that a = 300mm and b = 420 mm 2mm 5mm-> 2mm…

A:

Q: Find the stress in the rod having a diameter of 20 mm, subjected to 10 kN force. If the material of…

A:

Q: Problem 2 The series of bars shown have their diameters from left to right decreasing by 3 mm, and…

A:

Q: Strains measured in a, b and c directions are yardımıa=-150x10-6, ɛb=200x10-6, and ɛc=300x10-6 with…

A: Given Data  ɛa =-150x10-6 ɛb =200x10-6 ɛc =300x10-6 E=200 GPa Poisson ratio ν= 0.3

Q: Solve this problem using Mohr's circle technique.

A: given strain in X direction, εx=150×10-6strain in Y direction, εY=200×10-6sheer strain on  XY plane,…

Q: K ДИЛ C D E F B 3 m |-2 m-2 m-2 m-+-2 m++2 m+/-2 m-| 20 kN 30 kN 40 kN G Find the Internal Force in…

A: Given - Truss Determine - the internal force in member BL

Q: The 1900-NN load is applied along the centroidal axis of the member. (Figure 1)   Determine the…

A: The 1900 N load is applied along the centroidal axis of the member. (Figure 1)1) Determine the…

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.