The spring index of a helical spring is calculated by the following: (a) Ratio of wire diameter to mean coil diameter. (b) Force per unit cross-sectional area of spring (c) Force required to produce unit deflection (d)Ratio of mean coil diameter to wire diameter. Which one is correct? O a. Option (a) only O b. Option (d) only Oc. Option (b) only O d. Options (C) & (d) only

The spring index of a helical spring is calculated by the following: (a) Ratio of wire diameter to mean coil diameter. (b) Force per unit cross-sectional area of spring (c) Force required to produce unit deflection (d)Ratio of mean coil diameter to wire diameter. Which one is correct? O a. Option (a) only O b. Option (d) only Oc. Option (b) only O d. Options (C) & (d) only

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please I want answer of this question. Thanks
Considering Figure 20-8 (textbook), the torsion geometry parameter, Jw, for case 2 when b=6 and d=9 is most likely: 400.5 562.5 283.5 60.8 279.0 392.6 386.0 572.6 184.1
(b) A passenger car has a tyre spring rate of 18,900 N/m. The front suspension rate is 1,450 N/m and the rear is 1,050 N/m. Assume the front tyres are loaded to 10,000 N and rear tyres are at 7,900 N. (i) Solve the front suspension ride rate in N/m. (11) Evaluate the natural frequency at front suspension.
S 4
A force of F = 50 N is applied to the rope that causes the angle 0₁ = 60 degrees to keep the system at equilibrium. The N spring constant is k = 100 m B a 0₁ с a b с Variable Value 2 m 2 m 2 m F b Values for the figure are given in the following table. Note the figure may not be to scale. cc i❀O BY NC SA 2013 Michael Swanbom
Q.4 (a) An electric motor of mass 50 kg is suspended from a support structure on a four-spring system. The springs are arranged in series, with the four stiffnesses being 15 kN/m, 25 kN/m, 30 kN/m and 40 kN/m respectively. Viscous damping is present within the system and the damping ratio is 0.175. i) Produce a neat sketch of the system and state its equation of motion. ii) Determine the level of the viscous damping in the system. iii) Determine the amplitude of vibration of the motor 10 cycles after it is released from an initial displacement of 125 mm.
Subject: mechanical
P1 + a1 2g P2 L V? +z2 + hrarbing + hg,toplam hx,sürekli=f•5•2g 2g +z + hpompa.f + az7 pg pg hk.yerel hỵ,toplam= hx,sûrekli + hxyerel Wmil Nsp 2g Протра (gH)3/4 一()-)图)第-(m)G) 1/2 mil WB (DB WA DA Wmil.B (DB (DB Wmil = pgHỳntürbin ww, p1/2(gH)5/4 PB (WB HB WB WmilA PA wa) HA Nst Wmil = prwv(V; – rw)(1 – cosß) %3D At the best efficiency point with the experiments on the A turbine DA= 72 cm, Ha= 20 m, VA = 50 m³/s, PA= 998 kg/m3, na= 205 revolution per minute, Wmila= 9 MW values have been obtained. PB= 998 kg/m3, HB= 65 m, nB= 185 A new B turbine will be designed. According to this; a) B is the volumetric flow of the turbine (VB) (m/s) find as. c) Find the specific speed of turbine B. b) Find the power of turbine B. (Wmil.B)| 2,5 285 d) Find the diameter of turbine B. 245.3 MW 35 120 cm 361 211,5 MW 2.8 156 cm 180 190 MW 2,1 144 crm 255 182,7 MW 3,1 104 cm 375 250 MW 95 am
Q2/ A (spring-mass-damper) system has vibrating with single degree of freedom. the mass is (30 kg) and spring stiffness (k Determine the following: 3000 N/m). a) The Critical Damping Coefficient. Ccr b) The Damped Natural Frequency when C =
As shown in the figure below, a uniform bar with mass m moves freely along a vertical tube at one end, suspended from a spring, and moving along a horizontal tube. At this time, find the equilibrium state, and find the stability of each. (When the spring constant is k and x=0, the spring is not deformed.)
K1=0.74， K2=1.47, K3=3.10
1. 1100 A. 30% B. 1.1 m 1.0 m A F= 255 N 0.5 m 1.5 m DGB WARNING! The figure is not drawn to scale. For the force in the chain CB, ca IMAGES NOTES DISCUSS UNITS STATS HELP PREFERENCES Part Description the magnitude of component parallel to the hinge axis of the door, (include units with answer) 0.5 m Answer 118.77 N Format Check the magnitude of the component parallel to the edge of the door that 218.17 N is perpendicular to the hinge axis, (include units with answer) Format Check Save 25 pts.7 75% 5% try penalty 31.67 pts.95% 5% try penalty Status Tr ● W #tries: ** Tr • W. #tries: