A spring balance is calibrated in an environment at a temperature of 25°C and has the following deflection/load characteristicsLoad (Kg)6.Deflection(mm) p30It is used in an environment at a temperature of 40°C and the following deflection/ load characteristics.Load (Kg)2Deflection(mm) 450Determine zero drift per °C and sensitivity drift per °C change in ambient temperature.SENSITIVITY DRIFTSENSITIVITY DRIFT/CZERO DRIFTZERO DRIFT/ C

Answered: Image /qna-images/answer/17451609-8051-4899-b326-0f2847bc81c0.jpg

A spring balance is calibrated in an environment at a temperature of 25°C and has the following deflection/load characteristics Load (Kg) 6 Defiection(mm) 30 It is used in an environment at a temperature of 40°C and the following defiection/ load characteristics. Load (Kg) 2 Defiection(mm) 50 Determine zero drift per °C and sensitivity drift per °C change in ambient temperature. SENSITIVITY DRIFT SENSITIVITY DRIFT/Pc ZERO DRIFT ZERO DRIFT/ C

A spring balance is calibrated in an environment at a temperature of 25°C and has the following deflection/load characteristics Load (Kg) 6 Defiection(mm) 30 It is used in an environment at a temperature of 40°C and the following defiection/ load characteristics. Load (Kg) 2 Defiection(mm) 50 Determine zero drift per °C and sensitivity drift per °C change in ambient temperature. SENSITIVITY DRIFT SENSITIVITY DRIFT/Pc ZERO DRIFT ZERO DRIFT/ C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Dynamics of Rigid Bodies Please help ASAP. Rate will be given accordingly. Please write your answer on paper. Thank you so much. Note: The number of significant digits is set to 3. The tolerance is ±1 in the third significant digit. I need Answer after 40 minutes.
C27 Which of the following is not a base SI unit? С. cd В. Hz A. kg D. mol C28 What is the percentage change in resistance of a semiconductor strain gauge with a temperature coefficient of 2e-5 °C-1, gauge factor of 2.1, under a strain of 1 µ at 100 °C. A. 0.15% B. 0.25% C. 0.2% D. 0.1% 15 C29 Consider a hydraulic press that lifts a weight of 128 kg by applying a 4 kg force. What is the ratio of area of the 'load' piston to the area of the force' piston? С. 16 А. 32 В. 4/2 D. 64
A digital meter is used to determine the torque of a rotating shaft using single toothed flanges and inductive pick-ups. Static calibration show that the flange twist by an angle of one degree for an applied torque of 1000 Nm. In a test with the shaft rotating at 500 r.p.m., the torque calculated from the timer readings is 1200 Nm. What is the maximum possible error of final digit on the timer display represents units of 10^-5 se and accuracy of instrument specified 0.05% of the reading ± 1 in the final digit? Read again don't copy last answer was totally different from questions
The force-deflection relation of a steel helical spring used in an engine is found experimentally as F(x): 100 x + 30 x² + 5x³, where the force F and deflection x are measured in N and cm, respectively. If the spring undergoes a steady deflection of 0.3 cm during the operation of the engine, determine the equivalent linear spring constant of the spring at its steady deflection. =
A beam subjected to a bending moment undergo a normal stress. A study was done and a sample was obtained with the following statistical parameters: Mean stress value = 452 MPa Value of the standard distribution = 21.4 MPa. The beam is made of steel with: Mean value of yield strength = 540 MPa Value of the standard distribution of yield strength = 38.4 MPa. If the strength and stress have normal distributions, determine the reliability in % considering yielding.
Free Vibration Acceleration Time History 0.5 1,-0.424 sec Accel, 0.423 g 0.4 0.3 t4.958 sec Accel0.194 g 02 0.1 -0.1- -0.2 -0.3 -0.4- -0.5 Time (sec) Calculate the natural frequency of the structure from the experimental testing results shown below which were obtained from a free vibration test of the SDOF structure. Acceleration (
A 1:40 scale of a submarine propeller is tested in a towing tank ar 1500 rpm and exhibits a power of1.4 ft-lb/s. Using Froude scaling law, determine the rpm and power output of the prototype propeller under dynamically similar conditions.
A strain-gauge measurement system is mounted on an airplane wing to measure wing oscillation and strain during wind gusts. The strain system has a 90% rise time of 100 ms a ringing frequency 0f 1200 Hz and a damping ratio of 0.8. Estimate the dynamic error in measuring a 1-HZ oscillation. Also estimate any time lag. Explain in words the meaning of this information
A spring balance is calibrated in an environment at a temperature of 25°C and has the following deflection/load characteristics Load (Kg) 6 Deflection(mm) b 24 It is used in an environment at a temperature of 35°C and the following deflection/ load characteristics. Load (Kg) 6 Deflection(mm) 4.5 29 Determine sensitivity at 25°C, sensitivity at 35 °C and zero drift per °C change in ambient temperature. sensitivity at 25°C sensitivity at 35°C ZERO DRIFT ZERO DRIFT/°C
A cylindrical steel bar 8 mm in diameter is loaded 1000 cycles per day with a load of 15560 N. How long until fatigue failure takes place? Note: stress = force/area Group of answer choices The bar should not fatigue. The bar will fail in one cycle. 100 days 1000 days
I need answer within 20 minutes please please with my best wishes