The slider block A is moving downward at v₁ = 7 m/s. (Figure 1) Figure B 250 mm 400 mm 30° D 300 mm 300 mm 1 of 1 ▼ Part A Determine the x and y components of the velocity of point E at the instant shown. Express your answers in meters per second to three significant figures separated by a comma. ΑΣΦ | 4t vec (VE). (VE), 3.424,-4.659 Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining Review Provide Feedback ? m/s Next >

Q: Solve for x.       x + 1   0 −1   x    = 2

A:

Q: The progressive or gradual engagement of the teeth of helical gears gives the ability to transmit…

A: Given data: The progressive or gradual engagement of the teeth of helical gears gives the ability to…

Q: How much force in lbs will it take to lift a 10 -lb weight with a wheel and axle, when the axle is…

A:

Q: A torque of 18 N m is applied to a rotating part. The part has a moment of inertia of 0.078 kgm2.…

A: Here we will use the the torque equation and the rotational motion equation.

Q: 27. You have the following compound machine. 60 teeth 40 teeth 20 teeth a. What is the speed of Gear…

A:

Q: nd the diameter and the number of teeth on both gears. plution:

A: Given data:Velocity ratio (VR)=5:1Centre distance (C) = 12inPitch (Pd) = 10

Q: Evaluate the following statement and determine whether it is True or False: "The specific heats for…

A: Specific heat (often denoted as "c") is a thermodynamic property that describes the amount of heat…

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: You are given two shafts of equal lengths and made from the same material: a hollow shaft, with an…

A:

Q: Question The figure below shows a hollow circular beam with an outside diameter of 250 mm and a wall…

A:

Q: Find ex, ey and y. NOTE: ex and ey in mm/mm and y in radians.

A:

Q: Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to…

A:

Q: The piston displacement of an air compressor is 1200 liters per minute. Its bore and stroke are 12…

A:

Q: R.75 00.63 THRU $5 01.123 0.250 E 1.38 0.63 mm radius hole partially through the part 0.63 mm radius…

A:

Q: 4. From the given figure, solve for the bar Y from the reference line . (choose the nearest answer)…

A:

Q: Determine the mass of a steel ball whose diameter is 16mm.

A:

Q: Please show the computation in solving for NB and FAB

A:

Q: A gear train consists of three gears: a pinion (which is the driver), an idler, and a gear (which is…

A: Given:- The gear train of three gears Tidler=68  Tidler(to replace)=37 To find:- Velocity ratio…

Q: Using the figure below solve for the desired degrees to be set in the compound rest. I TPF = .602…

A:

Q: solve 4 and 5 only

A: The given state of stress is:To find:(iv) The orientation of the elements for the maximum in-plane…

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: Given a gear of 32 teeth and 6 diametral pitch. Find the pitch diameter, outside diameter, tooth…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: An 4 cylinder engine has a crankshaft sp of 3,500 rpm, a bore of 3.8 inches, a str of 3.8 inches,…

A: Givenk=4N=3500 rpmd=3.8in =3.8×0.0254=0.09652mL=3.8in=3.8×0.0254=0.09652mP=210…

Q: QUESTION 2 A shaft rotates at 300 rpm. 1), If it carries a spur gear that delivers 5 hp to a mating…

A: Given: N=300 rpm

Q: 1. In the given figure, gear 1 has 24 teeth and gear 2 has 70 teeth of PD=4. Gear 3 has 20 teeth and…

A:

Q: solve a thru e show all steps

A: is normal reaction force between contacting surfaces.W is the weight force of the block. is the…

Q: For practical working gears as manufactured, typically the addendum, a, is larger than the dedendum,…

A: Addendum: The distance between the top land and the pitch circle on a gear tooth, is called as…

Q: a. Determine the magnitue of P and F (in N) if the resultant of the five force shown is 1000N…

A: The given system of force is as shown below, The given forces are as follows. F1=840…

Q: A piston engine in which the bore and stroke are of equal dimension is referred to as a "square…

A: Given:Let bore be 'D' and stroke be 'L'For a square engine, D = LNo of cylinders, n = 8Displacement…

Q: 5. I went for a 2 mile bike ride. With the given information below, how many times did I pedal my…

A:

Q: Mechanical properties of materials:   Strength of material:   Ultimate strength:   Yield…

A: Material property of property- To is critical to understand the mechanical properties of a material…

Q: 3. From the given figure, solve for the bar X from the reference line (choose the nearest answer)

A:

Q: A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth.…

A: Detailed explanation and solution of the above problem uploaded in below picture.

Q: 5 7 9. -1 8. A = 1 9. -1 -5 6 4 -7 3 -2 -3 0 8 Solve for the determinant of A. 63 3 7

A:

Q: Solve erf only

A: Given:To Find: the value of x.Note: In the above equation,

Q: 3. From the given figure, solve for the bar X from the reference line . (choose the nearest answer)…

A: note  you have give radius in cm unit but the option is given in mm , the magnitude is correct .

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.