The liter is defined as 1000 cubic centimeters. Convert 13 liter to gallon. 3.432 o gallon

Q: Convert 5 acre · ft to gallons. 1629020.1945o gallons

A: Given data 5 acre.ft to gallons

Q: determine the magnitude of the couple forces

A: Moment of couple:- Moment of couple is defined as the two parallel forces with same magnitude but…

Q: question carefully.  Give me all right solutions with clear calculations

A:

Q: Calculate the magnitude of the tension T and the angle for which the eye bolt will be under a…

A:

Q: You do not need to provide Given, Assume, and Problem Type/Features for this  question. You just…

A: DefinitionStatic Equilibrium:If a body is at rest and experiences zero force or zero torque, this is…

Q: The vectors A = 4i + 7j – 5k and B = xi + yj + 6k are known to be parallel. Find x and x = -4.8 -8.4…

A: Given that there are vectors ;Vector A→=4i+7j-5k and vectro B→ =xi+yj+6k ;And these vectors are…

Q: Refrigerant 134-a enters a compressor at 320kPa as a saturated vapor with a flow rate of

A:

Q: A golfer is attempting to reach the elevated green by hitting his ball under a low-hanging branch in…

A: Given data: Launch speed of the golf ball v0=115 mile/hr To find: 1. Launch angle θ=?…

Q: What is the weight of 12 kilogram object, expressed in lbf? 26.424 o lbf

A: Recall:- 1 kilogram = 2.20462 lbf  Weight of the object (W) = 12 kilogram

Q: b) Determine the hydrostatic force acting on the radial gate and its angle of inclination if the…

A: Given: The vertical height of the water from top to bottom of the gate, h = 15 m The length of the…

Q: Water flows at a rate of 2.4 ft3/s in an old, rusty 7.8-in.-diameter pipe that has a relative…

A: Given;

Q: (NOT IN SCALE) Determine the direction of angles of a force vector F, where 01 = 40°, 02 = 20°, and…

A: Write the force F in vector notation by projecting it components on the x, y and z axes…

Q: Determine the magnitude and the direction angles of a vector – 5i + 3j – 6k. Magnitude is…

A:

Q: Cable AB passes over the small ideal pulley Ćwithout a change in its tension. What length of cable…

A: To find: The length of cable CD is required for static equilibrium and the tension T in cable CD.…

Q: The steel structure (E=200GPA) shown in Figure Q4, is consisted of the solid bar, DC (length, L of…

A:

Q: If direction angles are B = 96° and y = 37°, then get the unit vector. û = 0.593 + ? -0.105 V o j+…

A: Given: Direction anglesβ=96oγ=37o

Q: A golfer is attempting to reach the elevated green by hitting his ball under a low-hanging branch in…

A: Given: Let us consider the given data, V0=112 mihr=50.0685 ms To find: The launch angle θ.

Q: Water flows at a rate of 2.4 ft³/s in an old, rusty 7.8-in.-diameter pipe that has a relative…

A: Given data:

Q: In the context of our teaching, which one of the below statements is mostly correct about in…

A: Component design, sometimes known as atomic design (though we prefer "Component design" at…

Q: Consider the pipe shown in the figure below. The nozzle's center line is 0.3 m above the flange…

A:

Q: 15. On the produced part below, show a simple sketch on how the flatness on the part m verified and…

A: Flatness:- It is defined as the minimum distance between two planes within which all the points on…

Q: Consider the stress element below. (a) Determine the three principle stresses and three shear…

A: given; stress in x direction(σx)=130MPa (tensile)stress in y direction(σy)=90MPa (tensile)stress in…

Q: What happens if you add a small imperfection to a system that has a saddle-node bifurcation?

A: A bifurcation is a shift in the qualitative nature of a solution as a control parameter is changed.…

Q: Sketch a meat tenderizer mallet. And can you show me the measurement of it.

A:

Q: (NOT IN SCALE) Determine the direction of angles of a force vector F, where 01 = 25°, 02 = 45°, and…

A:

Q: 6. A piston-cylinder device initially contains 0.07 m³ of nitrogen gas at 130kPaa and 180°C. The…

A: writing the equation for the polytropic process, P1V1K=P2V2KHere the initial pressure is p1, the…

Q: A hollow 3 m long steel shaft that will provide the main engine drive transmission for a ship to be…

A: Given data: Length of hollow steel shaft, L=3 m=3000 mm. Torque requirement is, T=25 kN.m=25×106…

Q: Water flows steadily with negligible viscous effects through a pipe shown on the right. It is known…

A:

Q: Determine the angular acceleration AB (positive if counterclockwise, negative if clockwise) of link…

A: The angular velocity of OB is θ˙=0 The angular acceleration of OB is θ¨=3.3 rad/s2 The angle is…

Q: Hello , i believe scale factor is 13 not 17. Does this affect the ongoing solution ? or if i just…

A: Given Data: Scale factor is 13 not 17.   To Find: Effect of scale factor on the existing solution.

Q: Calculate to the correct number of significant figures. (9443+45-9.9)x8.1x10^6

A: (9443+45-9.9)x8.1x106 77000000000 7.7×1010 (scientific notation)

Q: A rectangular gate that is 2 m wide is located in the vertical wall of a tank containing water as…

A: The depth of a submerged body determines the hydrostatic force acting on it. Its the mass centre of…

Q: Q#4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure.…

A:

Q: formulae

A: Assumptions i) water flows out to the open atmosphere from the valve outlet. ii) The tank is large…

Q: Four pets named Arjay, Baguilat, Cuh-ing, and Dabest play a pulling game with a rope as shown below.…

A:

Q: In (Figure 1), F = 100 lb. Follow the sign convention. Figure 800 Ib F 20 SIR 600 lb 36 < 1 of 1 ▾…

A: F = 100lb   To find: NC, VC and MC

Q: Determine Pa-PB if x = 3.0 m, y = 1.0 m, z = 2.5 m in the figure below. Fluid 1 and 3 is paraffin,…

A:

Q: Please show work for all these answers and a clear and short explantion of each one

A: Given the Fe-C Phase Diagram.

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.