The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.“). Assume that the support at D can provide resistance either up or down. For a loading of w = 6.5 kips/ft, determine: (a) the beam deflection VĄ at point A. (b) the beam deflection vc at point C. Assume LAB = 9 ft, LBc = 8 ft, LcD = 8 ft, LDE = 6 ft.

The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.“). Assume that the support at D can provide resistance either up or down. For a loading of w = 6.5 kips/ft, determine: (a) the beam deflection VĄ at point A. (b) the beam deflection vc at point C. Assume LAB = 9 ft, LBc = 8 ft, LcD = 8 ft, LDE = 6 ft.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rigid beam ABC supports a linear distributed load with maximum value q while supported by a pin at A and two deformable cables, DB and DC. The properties and cross-sections of the cables are shown below. The application is such that a factor of safety of at least 1.5 against yielding is needed at all times. a) Find the value of q required so that a horizontal displacement at point C equals 5mm. b) Find the safety factors of the cables. Are they within the requirement? Assume the cables remain elastic. For cable DB: diameter = 20 mm, Ecable,DB = 225 GPa, Oy,DB 300 MPa. For cable DC: diameter = 20 mm, Ecable, DC = are at the same vertical position. 70 GPa, Oy,Dc = 200 MPa. Note that points C and D 4 m q B 3 m 3m Figure 2.1. Rigid beam with distributed load
/stemezcom Lec3 working stres For the beam shown below, determine the concrete and steel stresses at the locations of the maximum positive and negative moments, Use ſ'c = 25Mpa. The answers are MPa, MPa, MPa and MPa. 3okN/m 8m 1m 4-25mmØ- -Top bars -4-16mmØ 250 250 bottom bars 630 630
No. 3. Beam AC carries a concentrated load P at its midspan point B. Determine the depth of the beam h in mm if the maximum bending stress is Omax = 50 MPa, the maximum deflection 8max = 10mm, the span is L = 4m, and the modulus of elasticity is E = 200 GPa. L/2 L/2- B 4+ 18. max
A bar AB is attached at A as fixed support. A small spaces can be seen on the other side of the bar prior to another rigid surface. Load P is applied on the bar located at two-thirds of length L from point A. Determine the small space s if the support reactions at A and B are to be equal due to the external load P. See all necessary parameters below. L A E P A 3 m 2500 mm² GPa 45 77 KN 2/3 -L 113 mm -L ANSWERS: ALL ANSWERS SHOULD BE IN THREE (3) DECIMAL PLACES INCLUDING ZEROS 01 (delta due to external load P) = 52 (delta due to Reaction at B) = Small Space s = mm S₁ mm B
Problem 2A beam with a rectangular section has a width of 250 mm and a height of 575 mm. It is reinforced with 4∅32distributed in two layers. Use fc’ = 30 MPa and fy = 400 MPa1. Check if this section will have a ductile or brittle behavior. Explain why2. Calculate the depth of the neutral axis.3. Find the strain in steel bars and strength reduction factor.4. Find the nominal moment capacity Mn.5. Is this section appropriate from the design point of view? And why?
A cantilever beam AB, loaded by a uniform load (see figure), is applied on a channel section. If the cross section has the dimensions indicated and the moment of inertia about the z axis (the neutral axis) is | = 3.36 in a) Find the maximum tensile stress feuaxand maximum compressive stress fyMx b) Draw the shear and moment diagram 5.0 lb/ft 0.617 in. 2.269 in. 6.0 ft
A simply supported beam is 0.6 feet long, and has a distributed load of 8.9 kips/ft pointing in the negative y direction along the entire beam. First- find the maximum moment in the beam? HINT: You should draw the beam. QUESTION: If the y distance from the neutral axis to the furthest fiber in tension is = -5 inches, and the moment of inertia of the beam is 100 in4, then what is the bending stress in the beam? in psi? Give answer to 1 decimal point, and no units, such as 1250.1 (not 1250.1 psi)
The frame shown below is subjected to an applied Point Load of 27kN and a Uniformly Distributed Load of 3kN/m and is supported at A by a pinned connection and at B by a roller connection. Calculate the vertical support reaction at B. Give your answer in kN to 2dp. 3m 3m PL UDL 5m A
A snow load transfers the forces shown to the upper joints of the Pratt and Howe roof lattices shown below. Ignoring the horizontal responses on the supports ( \(A x=Ex=0 \)) a) Determine the forces in all members using the joint method. Pratt Roof Truss System: AA A 2 Rods Pull Push CC=5,7 WIDTH (m) x=2 y=3,4 height (m) z=4,2 X 1 BB H 2 y 3 CC G y BB 5 D F X Pratt Roof Truss System SOLUTION: 6 AA E A 4-digit number must be written after the comma. For example 14.7845. Forces (kN) AA=4,2 BB=4,2 A
A field sand cone test is performed on a layer of compacted fill. determined that the fill soil has a maximum dry unit weight of approximately 120 pcf. Determine the relative compaction of the compacted fill. Unit weight of dry uniform of sand: 95 pcf Weight of sand to fill the cone: 1.10 lb weight of jar + cone + sand (before test): 16.5 lb Weight of jar + cone + sand (after test): 10.5 lb Weight of moist soil excavated from hole: 6.60 lb Moisture content of soil from hole: 10 %
Below presents a continuous beam with A being fixed and B is pinned and C has a roller. Take: E = 200 GPa 1 = 8 x 106mm Load = 2 kN A 5m B Using the following method: 2 KN + 2m + 2m |- You are tasked to analyze the continuous beam by calculating the: > the displacement on the beam at B and C and > the reaction at the supports Matrix Structural Analysis Use the following steps as a guide to analyze the beam: Matrix Structural Analysis ✓ Produce Notations ✓ Establish the known displacements and known external load ✓ Produce Member Stiffness Matrix ✓ Displacement and Load ✓ Calculating the displacement Calculating the reaction at the support
Determine the reactions for the beam shown if the vertical deflection at support B is zero. 3.0 kip/ft O B 16' 8' SIMPLE BEAM: CONCENTRATED LOAD AT ANY POINT SIMPLE BEAM: UNIFORMLY DISTRIBUTED LOAD Pb R = V, (max when a b) R V, . Pab w V M max (at point of load). M max (at center) Pbx Shear M, (when x b) = Pab(a + 2bN3a(a + 2b) M max Amax (at center), 27EI Pah2 384EI M max Moment A, (at point of load) 3EII WX (3 – 21r2 + x³) Pbx (2 - b2 - x) 4, 24EI 4, (when x