Question: Given: a = 0.4 m b=0.1 m A B F₁ = 800 Kn 0.7 m F₂ = 912 kN 1 m M₁ = 400 kNm 1) Find the shear force at Point A, VA: 2) Find the bending moment at Point A, MA:

Q: 1.1 A beam ABC 12 m long is simply supported at A and B where AB = 8 m. Point loads of 15 kN and 6…

A: Since, the question number to be solved is not specified, the solution for question 1.1 is as…

Q: 1. Figure Q1 shows a simplified diagram of a Ram Air Turbine (RAT), where the force on the rotor is…

A: Given values: Consider the given diagram of RAT. EI = 2.7 * 105 Nm2

Q: 3. A beam with the cross section shown in Figure 3 is subjected to an internal moment of X6 kNm,…

A: Given :

Q: The beam AB, shown in Figure 1a, with length L = 4.5 m  is subjected to a uniform distributed load w…

A:

Q: Determine Ay and By then draw a shear and moment diagram

A: A simply supported beam with uniformly distributed load and point loads.To find: Support reactions,…

Q: What are the support reactions at points A and B? What is the maximum bending moment and where does…

A: Step 1:Step 2:Step 3:

Q: F1 = 4 kN F2 = 3 kN F3 = 2 kN a = 3 m b = 5 m c = 4 m theta = 33 degrees Find the x-component of…

A:

Q: Q 2: A steel rod having a cross-sectional area of 300 mm and a length of 5.5 m is suspended…

A:

Q: A load P.is supported by a structure consisting of rigid bar BDF and three identical 18-mm-diameter…

A:

Q: As shown in the figure, the beam is supported by a pin support and a roller support at A B,…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: The rigid bar BC shown is supported by the steel rod AC of the cross-sectional area of 0.25in^2.…

A: Given: The cross-sectional area of steel rod AC is 0.25 in2. Consider the figure,

Q: A gusset plate for a bridge truss is shown in the figure. Determine the magnitude and direction of…

A:

Q: The three-bar truss ABC shown in the figure has a span L = 3 m and is constructed of steel pipes…

A:

Q: A circular table shown has a weight of 500 kN. It is supported at A, B, and C. Determine the…

A: To determine the reaction at B.   Given, Weight of the table, say W = 500 kN   We can determine the…

Q: The pin-jointed planar truss shown is subjected to a single downward force P at joint A. Consider 1…

A:

Q: /٤١٢ 9.5. A curved beam is built up by welding together rectangular and elliptical cross-section…

A:

Q: A w = 4 kN/m 10 m C B K= 40 kN/m

A: Length of beam = 10mE = 200 GPaI = 60 × 10⁶ mm⁴K of spring = 40 KN/m Udl load on cantilever of…

Q: Given the system above, F1 = 34 N, F2 = 96 N, M = 245 N-m, a = 3 m, b = 2 m, and a = 40°. (a)…

A:

Q: The vertical steel bars BE and CF supports the horizontal rigid bar ABCD and the applied forces as…

A: Modulus of elasticity of steel (E)=200GPa To find deflection at point A and D

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.