The shaft shown has an outer diameter of b = 0.625 in and a wall thickness of a = 0.092 in. The shaft will rotate at 2000 rpm. Determine the maximum power transfer possible with this shaft if the shearing stress in the shaft must be limited to 12 ksi. 2014 Michael a 0e0 Swanbom

The shaft shown has an outer diameter of b = 0.625 in and a wall thickness of a = 0.092 in. The shaft will rotate at 2000 rpm. Determine the maximum power transfer possible with this shaft if the shearing stress in the shaft must be limited to 12 ksi. 2014 Michael a 0e0 Swanbom

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 3: Design engineers in many situations must justify their selection of beams and pin-ended columns used in various machines. Your role in a mechanical design company that manufactures gearbox and gearbox mounting platform is to analyse the rolled steel beams and columns under study. Your manager asked you to properly select one rolled steel beam and one rolled steel column for the design and to provide your justification of this selection, if the following design requirements are given: - Beams and columns are made of ASTM-A709/Grade-345 Factor of Safety (F.S) is 1.2 Buckling Euler conditions must be met. Beams are subjected to 50 kN axial force. Beam (A) has radius of 10 mm. Beam (B) has radius of 5 mm. Column (A) is subjected to 15 kN axial force. Column (A) has length of 1.5 m and radius of 10 mm. Column (B) is subjected to 15 kN axial force. Column (B) has length of 1.5 m and radius of 13 mm. P P A B Figure.3: Rolled steel beams. P P A P P Id B Figure.4: Rolled steel…
Need only a handwritten solution only (not a typed one).
4. Schedule 40 pipe is to be used in a torsion application. The power applied is to be 200 hp and the pipe material is to be SAE 1141 OQT 900 steel. The loading is to be repeated. ( 400 RPM) Text book: Applied strength of Material 6th (a) Calculate the maximum allowable shear stress for the steel. (b) Calculate the smallest size of schedule 40 pipe
QUESTION 2 A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, Su 345 MPa) for the C-frame material. Calculate the bending moment about the centroidal axis upto 3 digits after decimal point in KN.m? 18 mm 38 mm 13 kN 25 mm 10 mm -90 mm 10 mm 1.805 Save A Click Save and Submit to save and submit. Click Save All Answers to save all answers. arch DELL
PLEASE ANSWER NUMBER 7.MECH 222-MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
SolveSample Problem 4.1.All remain as presented, except for the following changes.The factor ofsafety is now 2, and not 3.As Presented, the thickness of the tube is uniform. In the new one that you are solving,let the thicknessesof the top and bottom be the same,ttb, and the thicknesses of theleft and right be the same,tlr.Theheightand the width of the tube are still respectively 5 in and 3.25 in.As you make thesethickness changes,you are to keep thetotal mass of the tube unchanged. Answer the same questions (a) and (b).Explain your findings
4. Write the relations used for maximum stress when a machine member is subjected to tensile or com- pressive stresses along with shearing stresses.
Design of Machine Elements Assume you have a 30 mm in diameter AISI 1040 steel shaft welded on a rigid surface. Forces appliedto this shaft is given below. What would be length of the shaft considering the conditions as givenbelow;− 40 Nm torque is applied throughout the shaft (torque)− 100 kg load is applied at the end point of the shaft (bending)− 250 kg load is applied to push the shaft in the compression direction (normal force)− Factor of safety should be 2
Solve please with correct answer
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the steel rod caused by the 42758-Nload, using the following data: length of steel = 1.27 m, length of bronze = 2.06 m Area of steel = 522 mm, Area of bronze = 239 mm Modulus of elasticity of steel = 216 Gpa, Modulus of elasticity of bronze = 84 Gpa x= 0.69 m, y = 1.08 m, and z = 0.86 m. Round off the final answer to three decimal places. ... Bronze Steel Ey te z
QI: A double-threaded 30-mm power screw is 30 mm in diameter with a pitch of 6 mm. The coefficients of friction are 0.05 for the collar and 0.08 for the threads. The frictional diameter of the collar is 40 mm. if Tg=18 N.m: 1- Find the A vertical load on the screw, the torque used to lower the load and screw efficiency. 2- Compute all the stresses on the screw body that will cause by the load.
Please answer the problem with FREE BODY DIAGRAM AND COMPLETE SOLUTIONS. Also, box the final answer and explain the step-by-step solutions. Thank you! GUARANTEED UPVOTE!!!! STRENGTH OF MATERIALS Topics: Torsion Flanged Bolt Couplings Torsion of Thin-Walled Tube Helical Springs PROBLEM:The turbine motor moving at 378 rev/ min can produce 2.5 hp. The shaft diameter is 1.25 inches. Calculate the torque and shearing stress developed in the shaft.