The rods CE (A = 130 mm²) and DF (A = 250 mm²) are attached to the rigid bar ABCD as shown. Knowing that the rods are made ofaluminum, E = 70 GPa.AP45 cmB30 cm 20 cmCO60 cmD75 cm If a force of 73 acts at point A, what is the deflection at A, in mm?Add your answer

A 73 kN force is acting at point A. Cross sectional area of CE is 130 mm2 and cross sectional area…

Answered: The rods CE (A = 130 mm²) and DF (A =…

The rods CE (A = 130 mm²) and DF (A = 250 mm²) are attached to the rigid bar ABCD as shown. Knowing that the rods are made of aluminum, E = 70 GPa. A 45 cm P B 30 cm 20 cm CO 60 cm D 75 cm ...

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. Link BD is made of brass ( E = 103 GPa ) and has a cross-sectional area of 258 mm?. Link CE is made of aluminum ( E = 72 GPa ) and has a cross sectional area of 332 mm? . Determine the maximum force P that can be applied vertically at point A if the deflection of A is not to exceed 0.30 mm. 225 mm 150 mm -225 mm 125 mm
= P2.39 Two cylindrical rods, AC made of aluminum and CD made of steel, are joined at C and restrained by rigid supports at A and D. For the loading shown and knowing that Ea 10.4 × 106 psi and Es = 29 × 106 psi, determine (a) the reactions at A and D, (b) the deflection of point C. -8 in.- E A 1-¹-in. diameter Fig. P2.39 10 in.-10 in.. B. 18 kips C D 14 kips 15-in. diameter
The length of the 332332 -in.-diameter steel wire CD has been adjusted so that with no load applied, a gap of 116116 in. exists between the end B of the rigid beam ACB and contact point E. Knowing that E = 29 × 106 psi, determine where a 57-lb (w) block should be placed on the beam in order to cause contact between B and E. For contact, x < in.
Question 3: The block shown is made of a magnesium alloy for which E=150 GPa and 9 =0.35. Knowing that g= 100 MPa, determine (a) the magnitude of g, for which the change in the height of the block will be zero, (b) the corresponding change in the area of the face ABCD, (c) the corresponding change in the volume of the block. 25 mm 40 mm 100 mm
A 8-mm-diameter wire (E = 90 GPa) supports a tension load of 5 kN. If the total elongation of the wire must not exceed 14 mm, determine the maximum allowable length L of the wire. 5,000.00 N
Solve for the total elongation of the system shown. 15 kN 12 kN 20 kN 4m 5m 6m Steel Ø = 120 mm E = 200 GPa Aluminum Ø = 70 mm E = 70 GPa Bronze Ø = 25 mm E = 100 GPa
8. The A-36 steel wire AB has a cross-sectional area of 10 mm² and is unstretched when 0=45.0°. Determine the applied load P needed to cause 0=44.9°. a. 2.67 b. 2.57 с. 2.37 d. 2.47 400 mm 400 mm
P 1 mm 375 mm C Fig. P2.16
Question 1For the steel truss (E= 200 GPa) and loading shown in the figure, determine the deformations of members AB and AD, knowing that their cross-sectional areas are 2400 mm2 and 1800 mm2, respectively.
1. A steel plate 5 /16 in. thick is embedded in a horizontal concrete slab and is used to anchor a high- strength vertical cable as shown. The diameter of the hole in the plate is 3 /4 in., the ultỉmate strength of the steel used is 36 ksi, and the ultimate bonding stress between plate and concrete is 300 psi. Knowing that a factor of safety of 3.60 is desired when P=2.5 kips, determine (a) the required width a of the plate, (b) the minimum depth b to which a plate of that width should be embedded in the concrete slab. (Neglect the normal stresses between the concrete and the bottom edge of the plate.
2.43 plz
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 32.93 lb. Express your answer in three decimal places. P A 2 in. ↓ Q 30 in. B 3 in. 40 in. C