STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! Answer ASAP! The rigid beam shown is fixed to the top with the three (3) posts made of Steel and Aluminum.The post has the length as shown when no load is applied to the beam and the initialtemperature is 20°C.Consider the material properties below:MaterialE(GPa)Steel200Aluminum 70a (μm/m -°C)11.725.5SteelArea (mm)If the final temperature would increase to 60°C, determine the force supported by each post ifthe bar is subjected to a uniform distributed load as shown.250 kN/mAluminum800 mm21003000800 mmA. Force supported by the steel members (in Newtons)B. Force supported by the aluminum member (in Newtons)Steel550 mm

Answer For the given Parallel Composite arrangement of members we know that the change in length of…

The rigid beam shown is fixed to the top with the three (3) posts made of Steel and Aluminum. The post has the length as shown when no load is applied to the beam and the initial temperature is 20°C. Consider the material properties below: E (GPa) Steel 200 Aluminum 70 If the final temperature would increase to 60°C, determine the force supported by each post if the bar is subjected to a uniform distributed load as shown. 250 kN/m Material Steel a (μm/m - °C) 11.7 25.5 Aluminum Area (mm) 800 mm 800 mm A. Force supported by the steel members (in Newtons) B. Force supported by the aluminum member (in Newtons) 2100 3000 Steel 550 mm

The rigid beam shown is fixed to the top with the three (3) posts made of Steel and Aluminum. The post has the length as shown when no load is applied to the beam and the initial temperature is 20°C. Consider the material properties below: E (GPa) Steel 200 Aluminum 70 If the final temperature would increase to 60°C, determine the force supported by each post if the bar is subjected to a uniform distributed load as shown. 250 kN/m Material Steel a (μm/m - °C) 11.7 25.5 Aluminum Area (mm) 800 mm 800 mm A. Force supported by the steel members (in Newtons) B. Force supported by the aluminum member (in Newtons) 2100 3000 Steel 550 mm

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter3: The Structure Of Real Materials

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Similar questions

3. A steel bolt through a 31-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 81 degrees Fahrenheit. The cross-sectional area of the bolt is 0.09 sq. inch and the cross-sectional area of the tube of 0.30 sq. inch. a. Find the thermal deformation (in inches) of the steel bolt. (Write your answer to 6-decimal places.) b. Find the thermal deformation (in inches) of the aluminum tube. (Write your answer to 6-decimal places.) c. Find the stress (in psi) induced in the steel bolt by the temperature change. d. Find the stress (in psi) induced in the aluminum tube by the temperature change.
Help me please
200 mm 3 kg/m Al. 3280mm 350 160 mm 80 mm Find maximum stresses in steel and aluminum
A rigid bar, AB, is pinned at point B. Two other bars, AC and AD, are connected to point A to provide support for AB. We are investigating the behavior of this system under a specific load. Key Details: Bar properties: Material: Steel with Young's modulus (Esteel) of 200 GPa and coefficient of thermal expansion (a) of 11.7 x 10^-6 /°C. Cross-sectional area: AC: 1960 mm² AD: 1250 mm² Length: AC: √2 meters (square root of 2 meters) AD: 1 meter Inclination angles: AC: θ₁ (theta 1) = 30° from horizontal AD: θ₂ (theta 2) = 20° from horizontal Load on bar AB: Idealized linearly increasing load with a maximum value of 30 kN/m at point B. Problem Objectives: Determine the internal forces (axial forces) acting within bars AC and AD due to the applied load on AB. Calculate the displacement of point A in both horizontal (dA,x) and vertical (dA,y) directions.If the bar is cooled by 10°C, what would be the: Determine the internal forces (axial forces) acting within bars AC and AD…
A spherical stainless-steel tank having an inner diameter ‘D’, is used to store naturalgas at a pressure of ‘p’. The properties of the steel are as follows: yield stress in tensionis ‘T’; yield stress in shear is ‘S’ and modulus of elasticity is ‘E’. The desired factor ofsafety with respect to yielding is ‘F.S’.Determine the minimum permissible thickness t min of the tank. (D (mm)=620)( p (MPa)=25)( T (MPa)=1000)( S (MPa)=440)( E (GPa)=208)( F.S=3.4)
For the figure shown, determine the stresses of the wires and the elongation when the temperature change is 45°. Aluminum Steel Area 800 mm? 600 mm? E 70GPA 200GPA Coefficient of Linear 23 micro m/mC 11.7 micro m/m°C Expansion stel AL 3M zm 20 kuym
Policie Current Attempt in Progress A steel [E = 29900 ksi, a = 6.5x10-6/°F] bar is held between two rigid supports. The bar is stress free at a temperature of 72°F. The bar is then heated uniformly. If the yield strength of the steel is 45 ksi, determine the temperature at which yield first occurs. Answer: T= i °F
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
PROBLEM 2 A tri metallic bar is uniformly compressed by an axial force P-12KN applied through a rigid end plate The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has a diameter l0mm, the brass tube has an oute diameter of 15mm and the copper tube has an outer diameter of 20mm E for steel =210Gpa, E for brass = 100GPA and E for copper is 120GPA Calculate the compressive stress of each metal due to force P
A steel bar is heated from room temperature to 80oC while it is free to expand. The bar will therefore be subject to: A. compression B. tension C. no stress D. shear
6 A steel pipe with a 50 mm outside diameter and a 43.75 'mm inside diameter surrounds a solid brass rod 37.5 mm in diameter as shown. Both materials are joined to a rigid cover plate at each end. The assembly is free to expand longitudinally. The assembly is stress free at a temperature of 27°C. For steel, Young's modulus is 200 GN/m², and the coefficient of linear thermal expansion is 11.7x10-6 1/°C. For brass, Young's modulus is 93.33 GN/m², and the coefficient of linear thermal expansion is 1.872 x 10-5 1/°C. What is the stress in the steel tube when the temperature is raised to 121°C? brass rod (solid) 37.5 mm diameter steel tube 50 mm outside diameter 43.75 mm inside diameter
need help.