The Results for SVI Calculation of a Mixed Liquor Sample Weight of Filter Paper = 0.603 g Weight of Ceramic Dish = 75.09 g Volume of Mixed Liquor Sample = 100 mL Weight of (Filter Paper + Ceramic Dish + Solids) = 75.979g SV =300 mL/L Mixed Liquor What about the settleability for this mixed liquor?

The Results for SVI Calculation of a Mixed Liquor Sample Weight of Filter Paper = 0.603 g Weight of Ceramic Dish = 75.09 g Volume of Mixed Liquor Sample = 100 mL Weight of (Filter Paper + Ceramic Dish + Solids) = 75.979g SV =300 mL/L Mixed Liquor What about the settleability for this mixed liquor?

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A pipet is used to transfer 5.00 mL of a 1.25 M stock solution in flask "S" to a 25.00-mL volumetric flask "B," which is then diluted with DI H,0 to the calibration mark. The solution is thoroughly mixed. Next, 2.00 mL of the solution in volumetric flask "A" is transferred by pipet to a 50.00-mL volumetric flask "B" and then diluted with DI H,0 to the calibration mark. Calculate the molarity of the solution in vol- umetric flask “B."
Saved Normal BIIIU fxl Ix Actual mass used in solution prep (g) Volume solution prepared Measured conductivity (uS/cm) Substance 0.1 g Naci 0.1003 100 mL 1149 0.1 g Nal 0.10 100 ml 419 Calculate the mass of Nal that would be necessary to yield the same conductivity as the NaCl solution. Clearly show these calculations in your lab notebook. Saved T BII U X X + fr Normal
A pipet is used to transfer 5.00 mL of a 1.25 M stock solution in flask “S” to a 25.00-mL volumetric flask “B,” which is then diluted with DI H2O to the calibration mark. The solution is thoroughly mixed. Next, 3.00 mL of the solution in volumetric flask “A” is transferred by pipet to a 50.00-mL volumetric flask “B” and then diluted with DI H2O to the calibration mark. Calculate the molarity of the solution in volumetric flask “B.”
Chemistry HW need help. How to do these calculation base on the data that is given？
Don
6. Using the figure below, what is the composition of the vapor from a solution containing 20 grams of toluene and 40 grams of benzene? Show all your work. Composition Diagram For a Binary Mixture of Benzene and Toluene 383.3 378.3 373.3 368.3 363.3 358.3 353.3 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 mol Fraction of Benzene Temperature (K)
An empty beaker weighs 45.786, beaker with mixture of sulfate weighed 64.861. Then a preweighed watch glass 17.876 g, watch glass with dried Fe(SO4)3 weighed 39.258. Find the % of sulfate mixture?
The gravimetric determination of Ni2*: Ni (58.7 g/mol) was precipitated as Ni(DMG) : (288.7 g/mol). The volume of unknown solution in the sample -60.00 mL. The mass of empty crucible 30.107 g, the mass of empty crucible and precipitate = 30.300 g. Calculate the concentration of Ni* in the unknown in sample solution (in mg/L) is: 1. 0262X10 2. 0131X 10 3. 025.3X 10+ 4. 00.654X 10
A stock solution whose concentration is 25.00 mg/mL was provided. A primary standard solution was then prepared by transferring 5.00 mL of the stock solution into a 50.00 mL volumetric flask. The primary standard solution was used to prepare three standard solutions of different concentrations by taking different volumes of aliquots into three 25.00 mL volumetric flasks: Standard Solution #1 #2 #3 Amount of Primary Solution (mL) 5.00 10.00 15.00 Three 25.00 mL volumetric flasks were then diluted to mark with water. Questions #1 What is the concentration of the primary standard solutions, expressed in units of mg/ml? #2 Re-write the concentration of the primary standard solutions obtained from Q#1 in units of μg/mL. #3 Determine the concentrations of three standard solutions in units of µg/mL. #4 What is a requirement for a "blank" solution used in calibration in spectrophotometry? Page 5 (Experiment #3)
8 = filled CHM-202 Lab 1 Solids and Solutions Rev 1 G6-2022 Results: 1. Models of Crystalline Unit Cells Atomic Radius (radius of styrofoam ball) Volume of one atom (one ball, 4/3r¹) Measured unit cell length (1) [1.3] No. Atoms per cell [1.3] Ratio of 1/r [1.3] Geometric unit cell length (1) [1.5a] Volume of atoms in cell [1.5c] Total 3 Volume of Unit Cell [1.5c] Percent vol filled [1.5d] Percent free space. [1.5d] I atom Simple Cubic SC 6.15mm 118 6.9 172 Raw Data (Temperature vs. Time) Trial Time CHM-202 Lab 2 Freering Point Depression Rev2 06-2022 232.6 Temp Time d= 6.9 r = 3.24 Sum v=172²³² Body Centered Cubic BCC 8 lan a atom 2.3 7.96 344 531.45 B. Cyclohexane Solutions (Trial 4 if needed) Temp Time (include units!) (include units!) Face Centered Cubic FCC (CCP) 10.8cm 4 atom 7/12 3.13 Temp 5.26 688 1259-73 Time the pieces are not Temp