The plate shown in the figure is fastened to the fix by three 10mm diameter rivets. Compute the value of the loads P so that the shearing stress of any rivet does not exceed 70 MPa. Express your final answer in Newton to the nearest whole number. Do not include the unit in your answer. 180 mm 100 mm L 150 mm 130 mm

The plate shown in the figure is fastened to the fix by three 10mm diameter rivets. Compute the value of the loads P so that the shearing stress of any rivet does not exceed 70 MPa. Express your final answer in Newton to the nearest whole number. Do not include the unit in your answer. 180 mm 100 mm L 150 mm 130 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the state of stress at point q. The pipe has an inner diameter of D₁ = 1.0 in and an outer diameter of = 1.8 in. Use the exact expression for Q, if needed. Label the reultant forces on the cross section below. Report your answer (3x3 matrix) in psi to one decimal place. Do 4 in. Y 4 in. 150 lb 6 in. 50 lb 10 in. 200 lb 150 lb X N Y
Use Möhr's circle to solve the unknown values in the stress systems shown in figure 16.37. 30 MPа = 80 MPa max 70 MPа 105 MPа 60°
The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.6-in .-diameter pin at A, and the 0.26-in .-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5205 lb. Round off the final answer to two decimal places.
2 ft The members of the structure in the figure weigh 200 lb/ft. Determine the smallest diameter pin that can be used at A if the shearing stress is limited to 5000 psi. Assume single shear. B 4 ft 3 ft с 6 ft
The state of plane stress at a point is shown on an infinitesimal element below. Determine the stresses at the point on an element that is oriented 65° counter-clockwise from the x, y axes shown. Enter the shear stress on this rotated element Ta'y' (with correct magnitude and sign) in kPa correct to 3 significant digits below. 300 kPa y 400 kPa X 400 kPa 300 kPa
The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made from a rubber-like material that expands when the nut is tightened to secure the sanding sleeve placed over the outside surface. If the diameter D of the mandrel increases from 1.90 in. to 2.00 in. as the nut is tightened, determine (a) the average normal strain along a diameter of the mandrel. (b) the circumferential strain at the outside surface of the mandrel. Sanding sleeve Answers: (a) ED (b) &c= = i i Mandrel in./in. in./in.
Consider the contruction shown. Suppose that P₁ = 18 kN and P₂ = 9 kN. Determine the maximum average shear stress developed in each 12 mm diameter bolt. Express the answer to three significant figures and include the appropriate units. | P₁ P₂
The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made from a rubber-like material that expands when the nut is tightened to secure the sanding sleeve placed over the outside surface. If the diameter D of the mandrel increases from 1.95 in. to 2.05 in. as the nut is tightened, determine (a) the average normal strain along a diameter of the mandrel. (b) the circumferential strain at the outside surface of the mandrel. Sanding sleeve Mandrel Answers: (a) ED = in./in. (b) Ec = in./in. Save for Later Attempts: 0 of 1 used Submit Answer
STRENGTH OF MATERIALS (NO LONG EXPLANTION NEEDED. RATE WILL BE GIVEN) Two blocks of wood, 50 mm wide and 20 mm thick are glued together as shown. If P is 600N, the shearing stress in the glued joint is
The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made from a rubber-like material that expands when the nut is tightened to secure the sanding sleeve placed over the outside surface. If the diameter D of the mandrel increases from 1.95 in. to 2.05 in. as the nut is tightened, determine (a) the average normal strain along a diameter of the mandrel. (b) the circumferential strain at the outside surface of the mandrel. Sanding sleeve D - Mandrel Answers: (a) ED = i in./in. (b) Ec= in./in.
If the allowable shear stress is, Tallow = 60 MPa, determine to the nearest millimetre the smallest-diameter shaft that will support the loading as shown in Figure 2. 200 mm B 400 mm 75 mm F, - 3 kN 50 mm 350 mm D Figure 2 F₂ = 2 kN
The two pieces of wood, 2.59in. by 5.69 in., are glued together along the 60°joint. Determine the normal stress (in psi) in the glue if the shear stress in the glue is limited to 352 psi. Round off the final answer to three decimal places. 017 shear.png ... P A