The plant in the picture has mass of 29 kg, and is hanging at a distance of 2.2 meters from the wall. The horizontal rod has mass of 8 kg. Assume that its weight is evenly distributed, therefore it can be treated as a single force at the center of mass. The rod is 3 meters long, and there is a cable at a 28° angle supporting it at the end. Using the wall as the axis of rotation, find the magnitude of the downward torque, from both the weight of the rod and the weight of the plant. N.m The downward torque is balanced by the upward torque from the force of tension. Find the magnitude of the force of tension. T = F is the contact force between the rod and the wall. Using the other horizontal force in the problem, find the horizontal component of F (the normal force) that must be present for the rod to be at equilibrium. F = %3D There is a vertical force from a component of the tension, but this is not enough to balance the donward forces. Find the vertical force that must be present for the wall to keep the rod up. Fy = N.

The plant in the picture has mass of 29 kg, and is hanging at a distance of 2.2 meters from the wall. The horizontal rod has mass of 8 kg. Assume that its weight is evenly distributed, therefore it can be treated as a single force at the center of mass. The rod is 3 meters long, and there is a cable at a 28° angle supporting it at the end. Using the wall as the axis of rotation, find the magnitude of the downward torque, from both the weight of the rod and the weight of the plant. N.m The downward torque is balanced by the upward torque from the force of tension. Find the magnitude of the force of tension. T = F is the contact force between the rod and the wall. Using the other horizontal force in the problem, find the horizontal component of F (the normal force) that must be present for the rod to be at equilibrium. F = %3D There is a vertical force from a component of the tension, but this is not enough to balance the donward forces. Find the vertical force that must be present for the wall to keep the rod up. Fy = N.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Problem 10: Consider a bar, of length 4.5 m, shown in the figure, being acted on by F3 three forces, and constrained to rotate about it's left end. The magnitudes of the first two forces are 29 N and 33 N, and the first force is acting on the end of the bar at an angle of 43° as shown. F2 Part (a) What is the torque, in newton-meters, due to F1 on this bar relative to the left end? Use a coordinate system with positive directed out of sin() cos() tan() 7 8 9 НОМЕ asin() acotan() cotan() acos() E 5 6 atan() sinh() 1 * 3 tanh() O Degrees O Radians cosh() cotanh() + END - Vo BACKSPACE DEL CLEAR Submit Hint Feedback I give up! Hints: 0% deduction per hint. Hints remaining: 2 Feedback: 0% deduction per feedback. Part (b) What is the torque, in newton-meters, due to F, on this bar relative to the left end, if this force is acting at the midpoint of the bar? Use a coordinate system with positive directed out of the screen. , Part (c) What is the magnitude of the force F3, in newtons, if the…
The figure shows a jet engine suspended beneath the wing of an airplane. The weight of the engine is 14200 N and acts as shown in the figure. In flight the engine produces a thrust 7 of 54800 N that is parallel to the ground. The rotational axis in the figure is perpendicular to the plane of the paper. With respect to this axis, find the magnitude of the torque due to (a) the weight and (b) the thrust. (a) Number i (b) Number i Units Units 2.50 m Axis T 32.0⁰
The steering wheel of a car has a radius of 0.20 m, and the steering wheel of a truck has a radius of 0.30 m. The same force is applied in the same direction to each steering wheel. What is the ratio of the torque produced by this force in the truck to the torque produced in the car? Number i Units
At the presentation ceremony, a championship bowler is presented a 1.58-kg trophy which he holds at arm's length, a distance of 0.655 m from his shoulder joint. (a) Determine the torque (in N · m) the trophy exerts about the shoulder joint when his arm is horizontal. (Enter the magnitude only.) Carefully draw a diagram which shows the force F which produces the torque for this situation, the vector i which locates the point of application of the force relative to the shoulder joint and the angle 0 between the direction of these two vectors. See if you can write a relationship that will allow you to determine the magnitude of the torque i if you know the magnitude of the vectors i and F, and also the angle 0 between their direction. N · m (b) Determine the torque (in N · m) the trophy exerts about the shoulder joint when his arm is at an angle of 35.0° below the horizontal. (Enter the magnitude only.) Carefully draw a diagram which shows the force F which produces the torque for this…
One end of a meter stick is pinned to a table, so the stick can rotate freely in a plane parallel to the tabletop. Two forces, both parallel to the tabletop, are applied to the stick in such a way that the net torque is zero. The first force has a magnitude of 2.00 N and is applied perpendicular to the length of the stick at the free end. The second force has a magnitude of 6.00 N and acts at a 38.9° angle with respect to the length of the stick. Where along the stick is the 6.00-N force applied? Express this distance with respect to the end of the stick that is pinned. d= i >
The figure shows a jet engine suspended beneath the wing of an airplane. The weight of the engine is 11900 N and acts as shown in the figure. In flight the engine produces a thrust of 68600 N that is parallel to the ground. The rotational axis in the figure is perpendicular to the plane of the paper. With respect to this axis, find the magnitude of the torque due to (a) the weight and (b) the thrust.
A door has a width of 1 m. The hinge attaches the door on the left. Andrea pushes on the right end of the door with a force of 30 N at angle θ=30∘θ=30∘. Bob pushes on the door in the opposite direction of Andrea. He applies a force of 30N30N perpendicular to the door at the midpoint of the door’s width. Andrea applies a magnitude of torque of ______nm to the door.
The wheels, axle, and handles of a wheelbarrow weigh 60.0 N. The load chamber and its contents weigh 525 N. The drawing shows these two forces in two different wheelbarrow designs. To support the wheel- barrow in equilibrium, the man’s hands apply a force F to the handles that is directed vertically upward. Consider a rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the man’s force for both designs.
A person exerts a horizontal force of 42 N on the end of a door 96 cm wide. What is the magnitude of the torque of the force is exerted (a) perpendicular to the door and (b) at a 60.0 degrees angle to the face of the door?
The distance from the fisherman's hand to the tip of the rod is L = 1.94 m. A fish is on the line, and it pulls the line with a force of F = 110 N at an angle 37.0° below the horizontal. What is the magnitude of the torque (in N · m) exerted by the fish about an axis perpendicular to the page and passing through the fisherman's hand
The figure shows five torques applied to a stick. Each stick shown has the same length and is pivoted around the dot. Rank, from least to greatest, the magnitude of torque applied to the stick in each case. If any torques are equal in magnitude, note this in your ranking.
Each propeller on a King Air twin-engine airplane consists of three blades, each of mass 21 kg and length 121 cm. The blades may be treated approximately as uniform, thin rods. What is the rotational inertia of the propeller, and if the propeller is driven by an engine that develops a torque of 2650 N⋅m, how long will it take to change the propeller's angular speed from 1250 rpm to 1850 rpm?