The plane AB is submerged in water has a circular shape as shown in Figure D. The upper edge of the plane is 2.53 m below free surface of water along the wall of the tank. Determine the hydrostatic force of the water on the plane and the position of center of pressure. Neglect the atmospheric pressure.

The plane AB is submerged in water has a circular shape as shown in Figure D. The upper edge of the plane is 2.53 m below free surface of water along the wall of the tank. Determine the hydrostatic force of the water on the plane and the position of center of pressure. Neglect the atmospheric pressure.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Fluid mechanics
The reaction at the support A and B is?
A sphere (SG = 2.2) is at the bottom of a tank filled with 1,5m of water. The diameter of the sphere is 50cm. Solve the hydrostatic force on the upper hemisphere. O 2.09kN O 2.73kN O 2.57KN O 3.21kN
The U-tube is filled with water and A is open while B is closed. If the axis of rotation is at x= 0.2m. Determine the constant rate of rotation so that the pressure at B is zero.
Determine the horizontal and vertical components of the liquid pressure acting on the semicylindrical gate ABC, as shown in the figure. The width into the paper is 1 m. 1 m Liquid (s.g. = 0.88) 4 m B 3.8 m 1 m Fx=123.148 kN and Fy=22.078 kN O Fx=146.005 kN and Fy=28.125 kN O Fx=226.352 kN and Fy=48.953 kN O Fx=249.813 kN and Fy=55.512 kN O Fx=273.251 kN and Fy=59.802 kN O Fx=203.049 kN and Fy=40.981 kN O Fx=298.077 kN and Fy=64.148 kN O Fx=182.117 kN and Fy=36.173 kN Fx=318.195 kN and Fy=68.970 kN O Fx=158.078 kN and Fy=31.450 kN O +
A square lamina is immersed in water with one of the diagonals vertical as shown in given figure. Calculate the force on one side and the location of the centre of pressure. 0.6 m G G a = 0.6 m
A simply supported beam of length 7 m has a concentrated couple M of 10 kN-m applied at the right end. Determine the location of the maximum deflection from the applied load. O 2.75 m O 2.96 m O 2.50 m O 2.252 m Calculate the value of the maximum deflection. Use E = 200, 000 N/mm^2 and I = 60x10^6 mm^4. O2.62 mm O 131 mm 10.52 mm 5.26 mm
Question- A rectangular plate 1.2 x 3 m is immersed in a liquid of relative density 0.85 with its 1.2 m side horizontal and just at the water surface. If the plane of plate makes an angle of 50 with the horizontal, the pressure force on one side of the plate is IS h 50° B C.G. 3 m 1.2 m A
A pipe with a weight of 3.7 kg/m is attached to a wall such that all degrees of freedom are restraint. At the free end of the pipe a vertical load P=100 N pointing downwards is introduced with an excentricity of 100mm from the axis. The pipe has an length of 1m and is made of steel with the Young's modulus of 210 GPa and the Poisson ratio of 0.3125. The moment of inertia is l=19.7 cm“ whereas the polar moment of inertia J = 2 I. First, as part of the mechanical properties determine the Shear Modulus. Then determine the total vertical deflection at the point where the vertical load is being introduced. Note: Use the principal of superposition. ANSWERS: Shear Modulus %3D [MPa] Vertical deflection due to weight only [mm] Vertical deflection due to End-Load (excentricity NOT considered) [mm] Vertical deflection due to excentricity of the End-Load only [mm] Total vertical deflection [mm]
A 2.8m square plate is completely immersed under water in a vertical position such that the two edges of the square are horizontal. It is immersed such that the center of pressure is located 8cm below its center of gravity. Determine the distance of the top of the plate from the water surface. O 6.8m O 6.3m O 7.3m O 7.8m