2. The disk of 50 N weight rests on two smooth inclined planes shown in the figure. Determine the reaction forces at A and B which are points of contact between the disk and inclined planes. C is the center of mass of disk. (30 Points) B A 30° 45°

2. The disk of 50 N weight rests on two smooth inclined planes shown in the figure. Determine the reaction forces at A and B which are points of contact between the disk and inclined planes. C is the center of mass of disk. (30 Points) B A 30° 45°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve the following with a free body diagram.
Set-up the overall stiffness matrix necessary to compute the nodal displacements at B and C. Compute the member forces of AB and BC and then determine the reactions at A and C. El=constant. 30 KN/m A 6m B 4 m
The figure shows a sphere resting in a smooth Vshaped groove and subjected to a spring force. The spring is compressed to a length of 125 mm from its free length of 150 mm. If the stiffness of spring k= 10 N/mm and weight of sphere is 100 N. Determine the contact reactions at the point A and B. 30° eeee • W 60° 1
Find the minimum value of P which will make it: a.) Slipb.) Tip Over
Set-up the overall stiffness matrix necessary to compute the nodal displacements at B and C. Compute the member forces of AB and BC and then determine the reactions at A and C. El=constant. 30 KN/m 6 m. В 4 m
4) Wire is being drawn at a constant rate from a spool by applying a vertical force P to the wire as shown. The spool and the wire wrapped on the spool have a combined weight of 20 lb. Knowing that the coefficients of friction at both A and B are 0.2 and 0.5, respectively. Determine the required magnitude of the force P. 5 in. 4 in. P A B
USE DOUBLE INTEGRATION METHOD.
A simply supported beam of length 7 m has a concentrated couple M of 10 kN-m applied at the right end. Determine the location of the maximum deflection from the applied load. O 2.75 m O 2.96 m O 2.50 m O 2.252 m Calculate the value of the maximum deflection. Use E = 200, 000 N/mm^2 and I = 60x10^6 mm^4. O2.62 mm O 131 mm 10.52 mm 5.26 mm
For the beam and loading shown, determine the internal bending moment at point "a" in kN.m. Consider F = 4 kN and wo = 6 kN/m. Ignore the weight of the beam. 2.5 m→ F wo A Co 6 kN.m 8 m a. ·2 m⋅ B
The small collar of mass m = 0.56 kg is released from rest at A and slides down the curved rod in the vertical plane with negligible friction. Find the velocity v of the collar as it strikes the base at B. Set b = 0.40 m, h = 1.66 m. Answer: VB i m/s
4. The engine hoist is used to support the 160-kg engine. Determine the force acting in the hydraulic cylinder AB, the horizontal and vertical components of force at the pin C, and the reactions at the fixed support D. (g = 9.81 m/s²) 1250 mm 350 mm D Bo 850 mm 550 mm
A uniform bar AB is resting in a horizontal position on smooth inclines as shown below. Determine the load P that will hold the bar in equilibrium. Also, determine the reactions at A and B. 411 N 2m 7m 1m A 60° 450