3. A cube, 60 cm on an edge, has its upper halfhaving a specific gravity of 0.60 and the lower half 1.40. It is placed in a two-layered liquid. Find the value of z iquid suface S 0.90 60 cm $ = 0.60 30 cm $=120 30 cm S = 140

3. A cube, 60 cm on an edge, has its upper halfhaving a specific gravity of 0.60 and the lower half 1.40. It is placed in a two-layered liquid. Find the value of z iquid suface S 0.90 60 cm $ = 0.60 30 cm $=120 30 cm S = 140

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A plastic rod with length and radius of 300 mm and 30 mm, respectively. If an axial force of 400 N is applied, estimate the length and diameter change. Young’s modulus and Poisson’s ratio of the material are 2.7 Gpa and 0.4 respectively.
I was wondering in the hydrodynamics how i can determine Cp in the pressure ressistance (coefficient pressure). so the total ressistance will be Rt= Rf+Rp. Given in Coefficients it will be: Ct=Cf+Cp now they say Cp in % of the friction coefficient (Cf). Ct=(1+k)*Cf with 1+k the formfactor. so the total ressistance will be Ct=Cd*1/2*ρ *v^2*S (wetted area m^2, v= velocity in m/s and ρ= 1025 kg/m3 for salt water) kan you explain me how to calculate the Cd in the total resisstance?
A cylinder weighing 20 pounds slides in a free pipe as shown in the figure. The clearance between the cylinder and the pipe is 0.001 in and it is filled with oil of relative gravity 0.80. If the cylinder is observed to decelerate at the rate of 2 ft/s^2 when the speed is 20 ft/s. Calculate dynamic and kinematic viscosity W = 20lb u = ? %3D %3D S oil = 0.80 p = ? %3D V = 20ft/s %D ccciinther Bripelgne epinder 5 inches
A material has a stress-strain relationship that can be approximated by the equation 3 € = 0.3 × 10-¹6 × ³ where the stress is in psi. Find the secant modulus and the tangent modulus for the stress level of 50,000 psi.
Q2)A filament 0.5m long and having a cross-sectional area of 1mm2 was stretched to breaking. If the breaking stress for the filament was found to be 109 Pa, calculate the mass which was hung on the filament to break it. Assuming the filament stretched linearly up to breaking, calculate the amount by which the filament stretched. (Young’s modulus for the material = 6 x 1010 Pa) If the assumption in (b) was justified, what might the material have been? State in one word.
There is no force on a beam, but the beam is subjected to a very large temperature difference above and below. As shown in the figure below, try to calculate the vertical displacement of the midpoint of the beam, assuming that the temperature coefficient of the entire beam is a = 11.7×10^-6 °F. Tip: See Mechanics of Materials for Beam Deformation Geometry
Problem 1: A. What is the largest mass block B can be without sliding down the plane? B PB -HA PC Given: MA = 1.5 kg, μA = 0.22, μB = 0.37, μc = 0.03, 0 = 30° (Answer: MB = 10.6 kg)
The lower ends of the three bars in the figure are rigid homogeneous W = at the same level before the 100 kN block is attached. The temperature of the bars is then increased by 80°c. The block is assumed to remain horizontal after all deformations have occurred. The properties of the bars are shown in the table. STEEL BRÖNZE Length, L Area, A Modulus of Elasticity, E Coefficient of Thermal Expansion, a 1.0 m 1.6 m 500 mm2 900 mm? 200 GPa 83 GPa 11.7x10-6 mm/ (mm-°c) 18x10-6 mm/ (mm-°C) Calculate the stress developed in the bronze bar. Bronze Steel Steel A Calculate the stress developed in the steel bar. FIGURE 10
Question #1 A hole having a diameter of 75 mm is cut out from a uniform plate of diameter 240 mm. The distance between the center of the plate and center of the hole is 50 mm. Determine the position of the center of gravity of the remaining material.
Four forces are applied to the machine component ABDE as shown. Determine the resultant acting at A. 200 mm A 40 mm | 50 N 20 mm 300 N 250 N 160 mm 100 mm 120 N
A body shown in figure 2 below consists of 2 parts. Part A is 0.75 the thickness of Part B. Part A has twice the density of Part B. There are 2 rectangle cut out 0.1m from the edges. (i)Find the centre of gravity? (ii)What would be the density of Part A as a % of Part B, for the CoG to be on the line y-y? Hint: Centroid of a semicircle is 4r/3TT 5m 2.5m T1m 0.5m Part A 2.5m JY Figure 2 Part B I