The pin-connected structure occupies the position under no load. When the loads G A (unknown) and H (16 kips) are applied, the rigid bar EF becomes horizontal. Bar AB 0.75in? 2.25in? is made of aluminum alloy (E=10,600 ksi) and bar CD is made of red brass (E=15, 000 ksi). Determine the weight E and the axial stresses in the E B D F 10,000 G H 4" 4" 2" two bars. 16"

The pin-connected structure occupies the position under no load. When the loads G A (unknown) and H (16 kips) are applied, the rigid bar EF becomes horizontal. Bar AB 0.75in? 2.25in? is made of aluminum alloy (E=10,600 ksi) and bar CD is made of red brass (E=15, 000 ksi). Determine the weight E and the axial stresses in the E B D F 10,000 G H 4" 4" 2" two bars. 16"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

need fast
Assume that the truss is simply supported at joints M and E. Determine the stress at member AH if P.= 15.375 Kips, the area is 11 in. Answer your problem with the given unit ksi. Pu Pu P. Pu P. P. P. * a w - LKJ IH G
Point B & C. Please complete solution and no rounding off.
b. Discuss how the figure below and determine the rigid bar BDE as used to support by two link AB and CD. 0.4 m 0.3 m B D 0.4 m 30 kN E 0.2 m The Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm2. Link CD is made of steel (E = 200 GPa) and has a cross- sectional area of (600 mm2). For the 30-kN force shown, determine the deflection a) of B, b) of D, and c) of E.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L1 = 50 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.7 ksi. Brass segment (2) has an outside diameter of 0.85 in., a wall thickness of 0.13 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.0 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
The question is below.
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T
Check the slenderness of the steel section against Local Buckling. 340 mm Use Fy = 800 MPa. O Compact Slender I O Adequate 400 mm None of the choices 30 mm 20 mm 20 mm
d(mm)=65 T(nm)=1500 Gst(Gpa)=70
Q19: In Figure below, what is the ratio of P to F h Waer Hinge Sec A-A
42 KN the cross-sectional area of each member is 600 mm² Determine the stress in member EF. Answer in MPa rounded-off to 2 decimal places AddSNUIF ana. 2m A Last saved 4:09:09 PM 1455 ET 2 m Next > Last >