The pin A, which connects the 200-kg steel beam with center of gravity at G to the vertical column, is welded both to the beam and to the column. To test the weld, the 80-kg man loads the beam by exerting a 300-N force on the rope which passes through a hole in the beam as shown. Calculate the moment of A supported by the pin. Welded pin A -1200 mm600- +600+ -300 mm mm

The pin A, which connects the 200-kg steel beam with center of gravity at G to the vertical column, is welded both to the beam and to the column. To test the weld, the 80-kg man loads the beam by exerting a 300-N force on the rope which passes through a hole in the beam as shown. Calculate the moment of A supported by the pin. Welded pin A -1200 mm600- +600+ -300 mm mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

How to solve this question step by step
A • Find all reaction through method of consistent deformations Note: (Moment & forces) at A and B you MUST introduce mid-span Draw moment diagram a pin connection at
Q-1 Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa.c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4.
(c) The rigid bar ABC is suspended from three wires of the same material. The cross- sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P shown. ----|--²--| A 9 DAB T L P Fig. Q1(c) PL Hint: S = note that ABC is a rigid bar. EA C
Situation 10: For the connection shown in the figure. Pu = 100 KN, x1 = 200, x2 = 200, y1= 50, y2 = y3 = y4 = 100 y1 y2 y3 y4 O 27 KN O 31 KN O 33 KN 0000 O 29.KN O O 1. Which of the following nearly gives the maximum force in the bolt due to the torque alone? x1 10000 x2
Identify and describe the functional classification of roads with respect to the following road agencies in Ghana; Ghana Highway Authority (GHA), Department of Urban Roads (DUR) and Department of Feeder Roads (DFR).
Problem 8: Determine the location ỹ of the centroidal axis i – i of the beam's cross-sectional area. Neglect the size of the corner welds at A and B for the calculation. -150 mm 15 mm B 150 mm -15 mm 50 mm
I need answers plss
Part A If the required clamping force at the board A is to be 85 N, determine the torque M that must be applied to the handle of the "C" clamp to tighten it down. The single square-threaded screw has a mean radius of 10 mm, a lead of 3 mm, and the coefficient of static friction is u, = 0.35. Express your answer to three significant figures and include the appropriate units. M = 1.1142 Nm O The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. Submit Previous Answers Request Answer Figure 1 of 1 Provide Feedback Next > M O Pearson