Answered: The outer diameter of the shaft is 100…

Engineering

Mechanical Engineering

The outer diameter of the shaft is 100 mm and the diameter ratio is 1.25. Find the polar modulus of the shaft is mm3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Asolid 15 mm diameter shaft is subjected to an axial load of P = 15 kN and a torque of Tacting as shown. If the largest shear stress in the shaft must be limited to 98 MPa, what is the largest torque T that can be applied to the shaft? Current Attempt in Progress T. P (1) В Part 1 Calculate the cross-sectional area and the polar moment of inertia for the shaft. Answer: mm2 A mm4
A composite spring consists of two close-coil helical springs connected in series. Each spring has 14 coils at a mean diameter of 20 mm. The stiffness of the composite spring is 800 N/m. If the wire diameter of one spring is 2.5 mm, find the wire diameter of the other. What will be the maximum load which can be carried by the composite spring and the Take G=78 GPa. corresponding deflection for maximum shear stress of 150 MPa?
The 75-mm rod carries a bending moment of 3kNm and a Torque T as shown in the figure. If the material fails at a maximum normal tensile stress of 125 MPa and at a maximum shear stress of 96 MPa, compute for the following: 3 kNm A. The maximum normal tensile stress experienced by the material when it reaches its maximum shear capacity. B. The maximum shear stress experienced by the material when it reaches its maximum tensile capacity. C. The maximum allowable torque which may be applied to the system such that the material will not fail.
A circular shaft of the dimensions shown in the following figure is subjected to three torques : T1 = 28 k-in, T2 = -8 k-in and T3 = 10 k-in. (a) What is the angle of twist of the right end due to the applied torque? (b) Plot the angle of twist diagram along the shaft. Let, G= 12×106 psi.
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to exceed 10000 psi, and the vertical deflection of joint D is not to exceed 0.600 in. when a load of P = 4300 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 88 in., b = 22 in., and c = 40 in. Part 1 * Incorrect Answer: C T= i 5.468 B Calculate the torque being applied to the shaft at point B. b Ib-in
A bending moment due to load applied on the head of femur bone which is offset by a distance (x= 50 mm) off the bone center for a person standing in relaxation.His weight is 70kg.1. Find the maximum bending stress induced due to the weight and compare it to the maximum comp. stress. R= 20mm t= 12mm.2. Draw the expression for the second moment (I) basing on min-wall hollow cylinder.3. Find the principal stress σ1, σ2, τx1y1, and the angle θp for point C and D shown.
The internal loadings at a cross section through the 120-mm-diameter drive shaft of a turbine consist of an axial force of 12.5 kN, a bending moment of 1.2 kN - m, and a torsional moment of 2.25 kN m. (Eigure 1). Figure 1.2 kN-m 12.5 kN 1 of 1 2.25 kN-m
The outer diameter of the shaft is 175 mm and the diameter ratio is 1.25. Find the polar modulus of the shaft is mm3. The polar modulus of shaft (in mm³)
2. The maximum torsional moment a solid shaft can bear is T = 0.2r kN . m. If the allowable shear stress of the material is [t] = 50 MPa, design the diameter of the shaft based on the strength condition
A hollow shaft is subjected to a maximum torque of 1.5 kN-m and a maximum bending moment of 3 kN-m. It is subjected, at the same time, to an axial load of 10 kN. Assume that the load is applied gradually and the ratio of the inner diameter to the outer diameter is 0.5. If the outer diameter of the shaft is 80 mm, find the shear stress induced in the shaft. help me
A hollow circular shaft of inner radius 20 mm, outer radius 40 mm and length 1 m is to be used as a torsional spring. If the shear modulus of the material of the shaft is 150 GPa, Calculate the torsional stiffness of the shaft (in kN-m/rad) is