The 75-mm rod carries a bending moment of 3kNm and a Torque T as shown inthe figure. If the material fails at a maximum normal tensile stress of 125 MPaand at a maximum shear stress of 96 MPa, compute for the following:3 kNmA. The maximum normal tensile stress experienced by the material when itreaches its maximum shear capacity.B. The maximum shear stress experienced by the material when it reaches itsmaximum tensile capacity.C. The maximum allowable torque which may be applied to the system suchthat the material will not fail.

Answered: Image /qna-images/answer/a9e8dfda-ca68-45fa-9b03-02fdd712eb65.jpg

The 75-mm rod carries a bending moment of 3kNm and a Torque T as shown in the figure. If the material fails at a maximum normal tensile stress of 125 MPa and at a maximum shear stress of 96 MPa, compute for the following:

The 75-mm rod carries a bending moment of 3kNm and a Torque T as shown in the figure. If the material fails at a maximum normal tensile stress of 125 MPa and at a maximum shear stress of 96 MPa, compute for the following:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A round beam of length 14-in is simply supported at A and D. The beam is loaded in torsion and with transverse loads. The diameter of the beam is 1.5in. Calculate the principal stresses and the max shear stress at the mostcritical point in the beam. solve from tan theta = 4/3 then theta =tan inverse(4/3) = 53.13 degree solve from theta for other force of 600 lb is theta = 45 degrees Then solve for each reactions, bending moment My, bending moment Mz and the maximum bending moment and maximum stress along x axis. And also calucalate the principle stresses and the maximum shear stress at the most crictical point in the beam. Show everything with proper digaram with step by step solution and give me right answer. And I will surely upvote for you and subscribe it.
For the rod in the figure, an allowable stress of 10 ksi, calculate the maximum torque T which can be applied. d= 0.5 in, D= 0.835 in, r= 0.045 in .
A single-piece bicycle crank is shown below under the following load: the rider pedals forward with a vertical force Fp = 500 N on the left pedal and no force on the right pedal. The chain exerts a force Fc on the chainring. The spindle is a solid cylinder with a diameter d = 16 mm. 1. Find the maximum normal stress and shear stress at cross-section y-y in image. Indicate the locations on the given cross section view where they act.
3. Four pulleys are attached to the 50-mm-diameter aluminum shaft. If torques are applied to the pulleys as shown in the figure, determine the maximum shear stress in each segment and the angle of rotation of pulley D relative to pulley A. Use G = 28 GPa for aluminum. a. Tab= b. Tbc= C. Tbc= ad= 1100 N·m 800 N·m D C 900 N·m 600 N m B A 2 m3 m2 m
A 28mm diameter steel shaft AB is built into a rigid wall at A and supported by a smooth bearing at B. The lever BC is welded to the end of the shaft. Load P 360 newton is applied as shown in the figure below. Determine the maximum shear stress and the angle of twist if the distance from A to B is 3 meters and the distance from B to C is .3 meters
A shaft fixed to a wall at B is made of an outer steel tube of 1" outer radius (G = 11,400 ksi) bonded to an inner solid brass core (G = 5200 ksi) of 0.5" radius. For the torque applied at A determine the maximum shear stress in each material and the rotation of A. Note: Each material carries part of the total applied torque. Treat end A %3D as a joint. Ans: 1977 psi steel, 451 psi brass 4 ft 0.5 in. 1 in. T= 250 lb-ft (a) all cunnorted at A and B. For
8-7 Determine the bending moment capacities around the horizontal axes for the cross-sectional areas with the dimensions shown in the figures. The allowable elastic stress is either 165 MPa or 24 ksi.
Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the shear stress occurring in the point.
The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5 kN. I Determine the tensile stress in each rod. Determine the shear stress in pin A between the members. If each rod is 600 mm long, determine the overall extension of the assembly. Ignore any stretch in the joint. 40 mm 5 kN. 30 mm 25 mm 5 kN
5 - A thin-walled pressure vessel is subjected to internal pressure p 1 MPa. What is the maximum allowable torque T, applied along the longitudinal axis, if the maximum allowable tensile stress is 80 MPa? ↓t=3mm 240mm polar moment of inertia J=2r³t
The hollow cylinder shaft shown in the figure has an inside diameter of 15mm and the gears are subjected to the indicated load. The bearings at points A and B only exert forces on the shaft in the y and z directions. If the allowable shear stress is known to be operm = 70 MPa. Use the maximum shear stress theory of failure and proceed to:a) Draw the bending moment diagrams My and Mz and torque T, determine the magnitude and location of the absolute Maximum Moment.b) Determine the outer diameter of the shaft to within 1 mm.
The rod shown below is of diamater 70 mm and is fixed at one end. It is subjected to 500 N.m and 300 N.m torsional moments as shown. Sketch the distribution of the internal torsional moment along the length of the rod. Also find the torsional shear stress at points A and B, and also the largest shear stress in the rod. Point B is to the left of the 500 N.m torsional moment and A is on the right of it. Round-up your answers to the nearest 1/100th of an MPa. y 35 mm 20 mm 500 N.m 35 mm- 300 N.m Torsional shear stress at A = MPа %3D Torsional shear stress at B = MPа Maximum shear stress = MPa %3D