A solid shaft is subjected to a twisting moment of 350 kNm. If the angle of twist is 5° per meter of the shaft and the shear stress is not to exceed 350 MPa. Determine the suitable shaft diameter by comparing the strength design and rigidity design. Also, determine the maximum shear strain acting on the shaft. Take G =225

Q: The A-36 hollow steel shaft is 2 m long and has an outer diameter of 40 mm. When it is rotating at…

A:

Q: A hollow aluminium tube used in a roof structure has an outside diameter 104mm and an inside…

A: A) Angle of twist for the given max shear stress in a hollow shaft: The angle of twist of a hollow…

Q: A propeller shaft is required to transmit 45 kW power at 500 rpm. It is a hollow shaft having inside…

A: Given data  Power transmitted = 45 kW Speed (N) = 500 rpm Inside dia (d) = 0.6*outside dia(D)…

Q: Torsion A hollow circular shaft has inside and outside diameters of 30 mm and 40 mm respectively.…

A:

Q: The allowable shear stress in two steel (G = 83 GPa) shafts below is 90 MPa. The design requires…

A: Given data, Shear modulus of the shaft, G = 83 x103 MPa Allowable shear stress, 𝞽allow = 90 MPa…

Q: Please don't use chatgpt. Give right answer

A: Step 1: Step 2:

Q: A solid steel shaft must not twist through more than 30 in a 6-m length when subjected to a torque…

A:

Q: Let's consider a solid circular shaft subjected to the torque loads as shown. Determine the minimum…

A:

Q: A cold drawn steel rod of circular cross-section is subjected to a variable bending moment of 565…

A: Calculate the mean bending moment. Mm=Mmax+Mmin2 Here, Mm is the mean bending moment, Mmax is the…

Q: A mild steel shaft of 50mm diameter is subjected to a bending moment of 1.9kNm. If the yield point…

A: Introduction The maximum shear stress hypothesis states that a material will fail or yield if its…

Q: À solid 0.96-in.diameter shaft is subjected to the torques shown. The bearings shown allow the shaft…

A:

Q: The internal loadings at a critical section along the steel drive shaft of a ship are calculated to…

A: Given data: The torque, T = 2300 lb-ft. The bending moment, M = 1500 lb-ft. The axial trust, P =…

Q: A solid shaft in a rolling mill transmits 30 hp at 100 rpm. Find the diameter in mm of the shaft so…

A:

Q: The dimensions of the cross section of an airplane fuselage are shown in figure 1. If the fuselage…

A: Given Data: The torque subjected to the fuselage is, T=8 MN·m=8 MN·m×1000 mmm=8×103 MN·mm. The…

Q: Determine the torsional shear stress in the shaft section AB and BC. There is a fixed support at C…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.