A mild steel shaft of 50mm diameter is subjected to a bending moment of 1.9kNm. If the yield point of the steel in simple tension is 200MPa, find the maximum torque that can be applied according to the Maximum Shear Stress Criterion.

A mild steel shaft of 50mm diameter is subjected to a bending moment of 1.9kNm. If the yield point of the steel in simple tension is 200MPa, find the maximum torque that can be applied according to the Maximum Shear Stress Criterion.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The maximum allowable shear stress in a hollow shaft of external diameter equal to twice the…

A: Given, Maximum allowable shear stress=80MPa Torques (T)=4000Nm Bending Moment (M)=3000Nm Let inner…

Q: (a) Determine the support reactions for the stepped circular shaft shown below. (b) Plot the…

A: GIVEN :- T1=200lb-inT2=100lb-inT3=500lb-indAB=3 indCE=2 inE=30×106psiμ=0.3SOLUTION :-Torque on…

Q: A solid shaft with a yield strength of 500 MPa subjected to a torque of 60N.m and bending moment of…

A: Step 1: Given data:Yield strength, σy=500MPaTorque, T=60N.mBending moment, M=70N.mStep 2: We need…

Q: Materials of mechanics questionUse figure below Parts A & B Part A - Based on the figure, give the…

A: A) External force is the member force plus the change in bolt force .Lets see the maximum and…

Q: A hollow circular steel shaft with an outside diameter of 2.569, and a wall thickness of 0.388 in.…

A: GivenPart 1D=2.569int=0.388inT=292 lb-ftL=124inG=12000 ksiPart 2D=2.915int=0.437inT=239 lb-ftL=105…

Q: A solid steel shaft must not twist through more than 30 in a 6-m length when subjected to a torque…

Q: A solid circular shaft of diameter 60mm is subjected to an axial stress of 20 MPa. It is further…

Q: A hollow shaft is to transmit 300 kW at 80 r.p.m. If the shear stress is not to exceed 60 MN/mm²…

A: Given that , P=300kW N=80 rpm Maximum shear stress = 60MN/mm2 internal diameter = 0.6 × external…

Q: Calculate the following: i. The polar second moment of area, J

A: Given data Outer Diameter of the shaft = Do = 50 mm = 0.05 mInner Diameter of the shaft = Di = 40 mm…

Q: A solid shaft of 150 mm diameter is used to transmit torque. Find the maximum torque transmitted by…

A: Given, Diameter of shaft = d = 150 mm Maximum shear stress = τ = 45 N/mm2 Polar moment of…

Q: Find the torsional shear stress on a 2 inch diameter shaft if it is subjected to a torque of 561…

A: Given diameter of shaft = 2 inch. Torque=561in-lb.

Q: A solid shaft in a rolling mill transmits 30 hp at 100 rpm. Find the diameter in mm of the shaft so…

Q: (a) The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer and…

A: Given data Outer Diameter of Tubular shaft = Do = 50 mm = 0.05 mInner Diameter of Tubular Shaft = Di…

Q: a solid rod with a circular cross-secton is subject to a torque of 253 N.m. if diameter of the rod…

Q: Find the diameter of a shaft to transmit twisting moments varying from 800 N-m to 1600 N-m. The…

Q: A mild steel shaft of 50 mm diameter is subjected to a bending moment of 2000 N-m and a torque T. If…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A mild steel shaft of 50mm diameter is subjected to a
bending moment of 1.9kNm. If the yield point of the steel in
simple tension is 200MPa, find the maximum torque that
can be applied according to the Maximum Shear Stress
Criterion.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the allowable stress in shear is 60 MPa, whatis the maximum permissible torque Tmax that may beexerted with the wrench?Through what angle f (in degrees) will the shafttwist under the action of the maximum torque?(Assume G = 78 GPa and disregard any bending ofthe shaft.)
A mild steel shaft of 50 mm diameter is subjected to a bending moment of 2000 N-m and a torque T. If the yield point of the steel in tension is 200 MPa, find the maximum value of this torque without causing yielding of the shaft according to: The maximum distortion strain energy theory of yielding
The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer and inner diameters respectively, and it is expected to be subjected to the following extreme loading conditions which act simultaneously: (a) A torque of 2.5kNm about the axis. A bending moment of 3.6kNm acting on the vertical plane containing the shaft axis. A 3.6 ENm 2-5m Figure 3(a) Calculate the following: i. The polar second moment of area, J
A solid shaft 125 mm in diameter transmits 120 KW at 160 rpm. Taking C = 8 x 104 N/mm2 and length of the shaft 7.5 m, find the maximum shear stress induced in the material of the shaft and the twist in radians.
Please help. Do not just guess. Prove your answer. I will give a good feedback. thank you :)
Two solid shafts, 50 mm in diameter, are connected by a flange coupling with six bolts and a pitch circle diameter of 95 mm. If the maximum shear stress in the shaft due to a torque is to be the same as the shear stress in the bolts, calculate a suitable bolt diameter. If the maximum working shear stress is limited to 55 MPa, what maximum power will be transmitted by the coupling at 700 r/min?
A drive shaft running at 2500 rpm has outer diameter of 60mm and innerdiameter of 40mm. The allowable shear stress in the shaft is 35MPa. Determine themaximum power that can be applied. Present drawings/FBD’s illustrating your solution.
Torsional T is applied to the hollow axis (G=80 GPa). Ewha Womans University, the maximum shear strain is γmax = 640 × 10-6rad Igo, inside andThe outside diameters are 120mm and 150mm, respectively.a. What is the maximum axial strain?b. Maximum axial stress?c. What is the maximum torque (T) meeting the above conditions?
Could you answer quickly pls? ( course: strength of materials 1)
For the circular shaft (G=12×106 psi) shown below: a. Compute the reaction torque and draw the torque (T) diagram. b. Find the max shear stress (Tmax) along the shaft. c. Compute the angle of twist AE at E. 1000 lb in 500 lb in 800 lb. in A B 2 in 2 in + 3 in D 5 in to E AC CD 2 DE
A shaft ABCD 70 mm in diameter is subjected to torques of 1500 N-m at B and 1100 N-m at C acting in the same direction. AB is 4m long, BC is 2m long and CD is 3m long. Supports A and D are unyielding and G = 80,000 MPa. (a) Calculate the maximum shearing stress of the shaft, (b) Find the rotation between A and C in degrees.
A cylindrical steel shaft is required to transmit a bending moment of 1000 Nm and a torque of 2200 Nm with a safety factor against yielding of 3. If the steel has a yield stress of 250 MPa, find the minimum permissible diameter for the shaft. Use von Mises’ theory of yielding.