Answered: A solid shaft of 150 mm diameter is…

A solid shaft of 150 mm diameter is used to transmit torque. Find the maximum torque transmitted by the shaft if the maximum shear stress induced to the shaft is 45 N/mm2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 1. If the power generated is 10 kW, determine the minimum allowable angular velocity of the shaft…

A: Given data: d=20 mmτ=60 MPa Need to determine the minimum allowable angular velocity of the shaft…

Q: A solid shaft is required to transmit 120 kW power at 200 rpm. Find the suitable diameter of the…

A: Power, P = 120 kW Speed, N = 200 rpm Tmax = 1.2Tmean Shear stress, = 70 N/mm2…

Q: For the steel shaft shown in Fig. Determine the maximum torque transmitted by any transverse cross…

A: For better understanding Draw the schematic diagram of the above problem.

Q: The maximum allowable shear stress in a hollow shaft of external diameter equal to twice the…

A: Given, Maximum allowable shear stress=80MPa Torques (T)=4000Nm Bending Moment (M)=3000Nm Let inner…

Q: The solid shaft (G=70 GPa) has a diameter of 40 mm. Calculate: a. The magnitude and direction of the…

Q: Torsion A hollow circular shaft has inside and outside diameters of 30 mm and 40 mm respectively.…

Q: The figure below show a stepped shaft in torsion. Compute the maximum shear stress at the step when…

Q: Solid shaft can resist a bending moment of 4.0 kNm and twisting moment 6.0 kNm together. Determine…

A: Given data, M= 4 kNm T=6 kNm Need to find maximum torque in shaft(Tm).

Q: A shaft is fixed at support C and has a torque of 75lb.ft with respect to free end at a distance of…

A: givenM1=75lbft at 0.75ft from fixed end CW2=1200lb/ft M2=600lbft at free end

Q: What must be the maximum torque of a 5mm diameter aluminum wire so that it can be twisted through 1…

Q: Find the torsional shear stress on a 2 inch diameter shaft if it is subjected to a torque of 561…

A: Given diameter of shaft = 2 inch. Torque=561in-lb.

Q: A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required…

Q: The dimensions of a stepped shaft are shown below. The maximum shear stress specification of the…

A: Given data: r=2.4 mD=15 mmd=12 mm Need to determine the allowable torque.

Q: Determine the outer and inner diameter (in mm) of a hollow shaft that is required to carry a bending…

A: This question is related to the shaft being subjected to both the bending moment and the twisting…

Q: A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required…

Q: A round steel shaft rotates at 200 rpm and is subjected to a torque of 275 N- m and a bending moment…

Q: A solid shaft of 200 mm diameter has the same cross-sectional area as that of hollow shaft of same…

A: Shaf dia=200 mmouter dia=300 mmto findthe ratio of power transmitted of solid

Question

A solid shaft of 150 mm diameter is used to transmit torque. Find the maximum torque transmitted by the shaft if the maximum shear stress induced to the shaft is 45 N/mm2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

The 16 foot long hollow steel shaft experiences a maximum shear stress of 8000 psi due to the torque of 100 kip. It's worth nothing that the shaft's inner diameter is two-thirds of its outer diameter D. Calculate: Calculate the D; the outer diameter Determine the shaft's twist angle For steel; use G = 12 x 106 psi.
For the steel shaft shown in Fig. Determine the maximum torque transmitted by any transverse cross section of the shaft. 17 ft kip 60 ft-kip GOGGOO 12 ft-kip 10 ft-kip T 25 ft-kip
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
A solid steel machine shaft with safe shearing stress of 7000 psi transmits a torque of 10,500 in-lb. A square key is used whose width is equal to one-fourth the shaft diameter and whose length is equal to 1.5 times the shaft diameter. Find the shearing stress in the key in psi.
Compute the torsional shear stress in a hollow shaft with an outside diameter of 40 mm and an inside diameter of 30 mm when transmitting 28 kilowatts(kW) of power at a speed of 45 rad/s.
Determine the diameter of a solid steel shaft which will transmit 112.5 kW at 200 rpm. Also determine the length of the shaft if the twist must not exceed 1.5o over the entire length. The maximum shear stress is limited to 55 N/mm2. Take the value of modulus of rigidity = 8 x 104 N/mm2.
The shaft consisting of steel and aluminum segments carries the torques T and 3T. Find the largest allowable value of T if the working shear stresses are 14000 psi for steel and 7000 psi for aluminum and the angle of rotation at the free end must not exceed 8°. Use G= 12 x〖10〗^6 psi for steel and G= 4x〖10〗^6 psi for aluminum.
A solid shaft (100 mm diameter) transmits 75 kW at 150 rpm. Determine the value of maximum shear stress set up in the shaft and the angle of twist per metre of the shaft length if G=80 GN/m².
A circular-closed-tube shaft, with an outer radius of 20 mm and an inner radius of 15 mm, and 650 mm long, is transmitting 50kW of power while rotating at a frequency of 20HZ. Compute the maximum shear stress (in Pa) and the angle of twist (in degree) for the shaft. The shear modulus G is 100 GPa. Hint: Please refer to the table of K and Q factors in the lecture notes.