The motorcycles mass: 170 kg The drivers mass: 64 kg I1= 0,26m I2=0,19m a) What is the needed acceleration so the front wheel will lift from ground? b) What is the needed supporting force on the rear wheel (in the cituation above)? c) What is the needed friction force (in the cituation above)? d) What is the friction coeffiecient (in the cituation above)?

Q: The shoes of a person playing ice skating experiences Select one: O Both static and dynamic friction…

A: Friction is defined as the force acting in the opposite direction of the motion.  For an ice skater…

Q: In a band brake, the diameter of the drum is 8 inches, and the angle of wrap is 210 degree. With a…

A:

Q: The car weighs 1600 lbs and drives up the hill at a constant speed. Assuming the static friction…

A:

Q: Two blocks are connected by a solid strut attached to each block with coefficient of friction 0.30…

A: Given Weight of the block B = 300 N Friction coefficient = 0.3 To find Force in the strut Weight of…

Q: : Two masses of 14 kg and 7 kg connected by a flexible inextensible cord rest on inclined plane…

A:

Q: Find the coefficient of friction Friction force=150 N Normal force=400 N

A: Given data : Friction force=F Normal force=N'   Required : Coefficient of friction

Q: Find the coefficient of friction Friction force=230 N Normal force=1200 N

A: Given data : Normal force=N' Friction force=f   Required : Coefficient of friction

Q: 1. A 200Kg box is on the platform of a weighing scale and is being pulled by a force of 70 Kg acting…

A: Solution:

Q: (Q2) The following data are given for the drum brake shown in figure (1) • Drum diameter is 400mm •…

A:

Q: The following data refer to a laboratory experiment with rope brake Diameter of the flywheel = 1 m;…

A: We have Diameter of drum, D=1 m Diameter of rope, d=10 mm=0.01 m Speed of engine, N=200 rpm

Q: 3- DESIGN CHANGE.  Now: The Object weighs 100 lb The angle of P above the horizontal is 42 degrees…

A: Given data  The Object weighs 100 lb The angle of P above the horizontal is 42 degrees The…

Q: a) A mechanie pushes a 70 kg wood box contains of an air compressor. The mechanic has a mass of 90…

A:

Q: Choose the correct value of coefficient of friction for the following data Friction force = 30 N…

A:

Q: In the Figure 3, if m=15 kg, 0-30°, and static coefficient of friction = 0.25, then the maximum…

A:

Q: 6. Point A is forcibly displaced 100 mm downwards and then let free. What is the type of resulting…

A:

Q: A 75-Kg man wants to pull a 145- Kg box and the coefficient of static friction between the box and…

A:

Q: Please check attach file

A:

Q: Coefficients of Static Friction: Steel on Rope: 0.3 Try to pull an Acme brand safe off of a stone…

A:

Q: For the drum brake figure shown below a) If a couple M of magnitude 1xy N.m is applied to the drum…

A: (a) Free body diagram the fig I and fig II showing the free body diagram of drum brake shown below…

Q: a) All Static Requirements b) frequency factor should be equal or higher to 15. c) Seq < Ses d) All…

A: For the helical compressive spring under fatigue load it must meet 1. All static requirements. 2.…

Q: Explain how a distributed normal force can be represented by a point force that moves as the…

A: Given:Distributed normal force can be represented by a point force that moves as the distribution of…

Q: QI-A 75-Kg man wants to pull a 145- Kg box and the coefficient of static friction between the box…

A:

Q: Find "a" of the below setup. Coefficient of friction is at u= 0.2 and the mass of every body, please…

A: Note: All bodies are connected and move as a single system,=&gt; Have same acceleration, a.

Q: Figure 2.1 shows a wheels vehicle mode. The mass of the vehicle is 1920 kg and the distance between…

A: Given data: Mass of vehicle = M =1920 kgDistance between Centre of mass and front axle = b= 1.5…

Q: A rope is hung over a stationary drum with weights on each end (100N; 400N). The rope is just on the…

A: given data : F2= 400 N F1=100 N the rope is just a point of slipping θ= 180 degreeswe need to find…

Q: A large shipping crate is at rest on the horizontal floor of a warehouse. The coefficient of static…

A: Given data as per the question static coefficient of friction (μs) = 0.500 Kinetic coefficient of…

Q: rev/min Q2: a/ an engine producing 12 kW power at 3000 rev/min is fitted to a vehicle with a mass of…

A: Answer:Given data:Engine power, Pengine = 12 kW = 12000 WEngine speed, Nengine  = 300 rev/minFinal…

Q: What is the frictional force between the 80kg block and the ramp? Given us = 0.2 and µ = 0.15. a.…

A:

Q: A 200 N wagon is to be pulled up a 30° incline at constant speed (see Fig. 2). How large a force…

A:

Q: Refer to figure 1. A wooden block stands motionless on a ramp.. Calculate the coefficier of static…

A: Given  (theta)=31.8 degree

Q: An Experiment Engine was subjected to various speed tests and the values ​​given in the table below…

A: GivenDensity of fuel=0.84kgarm length R=0.25mPatm=99.70kpaT=290kV=0.296dm3N=2000load=3.6kgTime to…

Q: As shown in the figure, two blocks of 4kg and 8kg are tied together on two inclined planes with a…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: The forces F, and F, in a brake band and direction of rotation of the drum are as show the figure.…

A: Given:Coefficient of friction, μ=0.25Angle of wrap, θ=3π2 rad.R= 1 m, F2=1 N

Q: a) What is the magnitude of the minimum force of static friction required to hold both blocks at…

A:

Q: Q.1 An externally contracting shoe brake shown below is actuated by a mechanism that exerts the same…

A: From the mechanical design handbook, we can obtain the actuating force , F   F = Mn+MfcWhere Mn is…

Q: I X,Lt) Ţ X₂ (t) ²k₁ = k m₁ = m { K₁=k ww M₂=M { K3=2K THTFILT The spring constants are K₁=k, K₂=…

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.