1. A 200Kg box is on the platform of a weighing scale and is being pulled by a force of 70 Kg acting at 43° above the horizontal. Between the box and the platform the coefficient of friction is 0.36. (a) How much will the scale register? (b) Will the box remain on the platform or slide? Prove your answer. P = 70 Kg 43 200 Kg WEIGHING SCALE

Q: Daw the Free buly Dingram

A: Free body diagram of given figure

Q: True or False: The JOIN command requires that line segments must lie end to end with no gaps or…

A: The JOIN command joins similar objects to form a single unbroken object. The JOIN command combines a…

Q: Describe How to mesh irregular volume by using ANSYS?

A: To mesh a volume with all hexahedron elements, the following conditions must be satisfied; 1.The…

Q: 5. ving gea Sun gear Arm planet gear The picture shows planetaury gear set : a A ssume the sun gear…

A: Given, 2 Sun gear 3 Arm 4 Planet gear 5 Ring gear T2=30T4=27 N5=0N2=101 rev/min

Q: The . drawings are the drawing that include all the information and instructions needed for the…

A: Drawing: A drawing is a representation of parts or assemblies by lines according to some certain…

Q: I need part 7 answered pertaining to the print and instructions.

A: The speed of the cylinder descent depends on the pressure of air supplied to the cylinder.

Q: Briefly describe what is meant by a right handed system of coordinate

A: System of cordinates -  A cordinate system is defined as a system which is used to define the…

Q: Make a representation of the layout of the Cartridge, the nomenclature and the scale on an A4 format…

A: It is asked to provide a representation of layout of the catridge

Q: I need parts 1, 2, and 3, answered pertaining to the print and instructions.

A: (1). The name of the circuit is HYDRAULIC CIRCUIT FOR 90 TON COMPACTION PRESS.

Q: I need parts 5 and 6 answered pertaining to the print and set of sequence of operations.   Note: If…

A: When the operator actuate the two-push button valves (1) and (2) until the weight starts to descend.…

Q: I need parts 8, 9, and 10 answered pertaining to the print provided and the set of sequence…

A: If intake and exhaust will be on the same side of cylinder head then this is a reverse flow and…

Q: The devices which prevent nuts from rotation and maintain them in their position are known as . .…

A: The nut is a device that is used to joint the component in the mechanical field. The Bolt is the…

Q: 6. What material is used 7. What is the unspecified tolerance for angular dimensions? 8. What is the…

A: Given figure  CHART DOWEL SPLIT TYPE  TO FIND :  7 .What is the unspecified tolerance for angular…

Q: What G-code designates IPM feed rate mode? IPR feed rate mode?

A: CNC machine feed rates are often specified in either inches per minute (IPM) or inches per…

Q: -D The above diagram represents which type of layout? Hybrid Layout Product layout Process Layout…

A:

Q: Basically a CNC machine runs on a program fed to it through Punched tapes Select one: True False

A: Computer Numeric Control (CNC): It is a machine which works on the computer program based on the…

Q: Procedure: • Create a detailed thread drawing for the fastener given below. • Save your drawing to a…

A: Kindly refer the next page to see the detailed drawing.

Q: means the repair work done to keep the system in good working condition.

A: we will discuss an activity/ process that is involved with work  done to keep the system in good…

Q: What happen when input II (push button) is pressed. 11 Q1 () Q1 Q2 O a. Ql -1 Q2 0 Ob.Ql-1Q2 1 Oc.…

A: The correct answer for the above mentioned question is given below. I am pretty sure of the answer.

Q: ch Liner (ID 6.270

A:

Q: Match each term with the correct definition. tool machine product system   a mechanical or…

A:

Q: Angle plate is a marking instrument used in workshops used to support workpieces during marking and…

A: It is required to justify given statement

Q: Which of the following is true about machine home, part origin, and tool change position? (choose…

A: Machine tool home is positioned set once by the machine manufacturer hence it makes second…

Q: Devise a mechanical models for the crane of the following Figure Steel cable W Steel boom

A:

Q: The Diagram below summerize what is a manufacturin system, can you explain it? Inputs Disturbances…

A: The manufacturing system is a set of interconnected equipment and human capital, the purpose of…

Q: explain the Frank-Read source multiplication mechanism

A: The frank read source is a mechanism based on dislocation multiplicationin a slip plane under shear…

Q: By using AutoCAD command draw the following samples with possible fitting. 1- Main door 2- Boiler 3-…

A: Given question: By using AutoCAD commands draw the following : 1. Main Door 2. Boiler 3.…

Q: (a) Why the connecting rod is made as I section? Why do some connecting rods have hole drilled from…

A: The connecting rod is a mechanical component that connects the engine's piston and crankshaft. In…

Q: The BREAK command: a. Will work on lines and arcs b. Will work on closed objects c. Can have the…

A: BREAK Command is a tool in AutoCAD software which is used for removing part of an object, open or…

Q: nance pr Tollowed wniie performing gib adjustment on a lathe machine is O On the front face of the…

A:

Q: Which one of the part definitions is right? O A part is an unit which is involved in the final…

A: Solution:

Q: he copy tools consists of a different commands namely D copy and offset

A: Ans: Option first is correct.  Copy and offset The copy tools consists of a different commands…

Q: ct one or more: Punch down tool is used to pull out the wire into the block hole and cut off the…

A: This question examines / tests the knowledge about the different tools electricians normally use.…

Q: Based on the image above, if the +Z jog button is pressed, turning the dial to the left will cause…

A: following is the correct answer to the above question-

Q: State and draw two methods used to mount cylinders?

A:

Q: How to perform zero point reset

A: Zero point reset is an introducing system for tenant discovery sensor that should be performed…

Q: contrast different input devices in cad/cam sections

A: CAD(Computer aided drawing) consist of input devices, output devices, processors.

Q: A one dimensional problem has ____degrees of freedom

A: Answer A one dimensional problem has ONE (1) degrees of freedom

Q: What is a coupling

A: Coupling is a commom word used in the field of mechanical engineering which means joining or…

Q: Which fixture would be the most suitable for welding up and drilling the holes for fixture for the…

A: Modular fixture is most suitable for welding up and drilling the holes for fixture for the complete…

Q: Which of the following is true about machine home, part origin, and tool change position? (choose…

A: option  b and c is correct  part origin is set by the programmer. all subsequent relative programmed…

Q: True or False: You can only use the REDO command immediately after using the UNDO command.

A: The UNDO command takes back the work in a drawing session whereas the REDO command will take the…

Layout

The layout is a way of organizing the elements, products, and raw materials in a design. The layout is the representation of information in a structural, logical, descriptive, coherent form.The layout is a mapping of various equipment arrangements, workstations, machinery, plants, and more. It secures the continuous movement of a product quantity along with the quality.