Briefly describe what is meant by a right handed system of coordinate

Q: A vector equation can be written as follows: A+>B-> C +>D = E +> F The directions for vectors A, B,…

A:

Q: 8. A single-acting reciprocating air compressor has a clearance volume of 10%. Air is received at 90…

A: Given data as per the question clearance volume =10%air recieved at 90 kpa and 302.3 kair discharged…

Q: PROBLEM: Based on the Orthographic Projections of the SHIFTER COLLAR draw a full section. +

A: Only one question is allowed to solve as per the bartelby guidelines.Based on the Orthographic…

Q: A manometer with water as in Figure 1.1. working fluid is connected to an air duct as shown

A:

Q: 2. A thin, homogeneous perimeter of the figure shown to the left. Locate the center of gravity of…

A:

Q: A metal disc of 50 mm diameter is to be punched from a sheet of 5 mm thickness. The punch and the…

A: Given that Disc diameter = 50mm Clearence = 3% = 0.03

Q: In this second part you are asked to analyze rocket propulsion with the present of gravitational…

A: Given Datawe have anlyze the rocket propulsion in the existance of…

Q: What is a polar coordinate system

A: In arithmetic, the polar coordinate system could be a two-dimensional arrange framework in which…

Q: 2 02 5 A 6 7 08 8 3 B с 9 4 D E

A: The J1 refers to the binary joints or the lower pairs in the given mechanism while J2 refers to the…

Q: create 2 fourbar designs that include the dimensions and angle of motion

A: It is asked to draw four bar mechanism with given motion

Q: Define translating coordinate system.

A: Coordinate systems are those systems which are used to specify the location of any point in space.…

Q: what the name of the coordinate system defined by Reference plane, Cutting edge plane, and…

A: Manufacturing Processes: The various processes involved in the manufacturing of a product starting…

Q: Draw velocity polygon.

A: Solution:

Q: he Lookout Hills gravitational slope-deformation feature in Bonne Bay, western Newfour plume of rock…

A: 306m wave height has been found in norris point.

Q: Estimate the flow rate Q of water discharging from the nozzle as shown in Figure 3. If the fluid…

A:

Q: A Dryer is to deliver 1000 kg/hr of palay with a final moisture content of 10%. The initial moisture…

A: A compressed air dryer is a piece of equipment used to remove water vapor or moisture from the…

Q: Which of the following settings does not allow you to control point specifications?a. Grid b. Snap…

A: From the given options, the snap, ortho and the polar settings are used to specify a point. Hence…

Q: In the FAPT programming language, the following format of statement Si= is used to define:…

A: Format of statement is a standard way of giving a command in FAPT language to perform any specific…

Q: What is translating coordinate system?

A: Let suppose a 2D coordinate system with origin O. position vector in this coordinate system is…

Q: Misrun is a casting defect which occurs due to

A: Given. Misrun is a casting defect which occus due to following conditions;where,Casting defect is an…

Q: 7. In a certain installation, a fan when driven by a 7.5 Hp motor at a speed of 600 rpm delivers 510…

A: The power required for fan driving is 11.12 Hp.

Q: 3. Find the centroid of the area shown to the right. Ans: =-0.241 in, %3D y =-2.58 in. %3D

A:

Q: ANSWER COMPLETELY FOR UPVOTE a. When do we say that the body is accelerating? b. What's the…

A: (a). When velocity of a body increases with respect to time, we say that the body is accelerating.…

Q: B 30° 3 m 2 m - 10 m

A:

Q: The horizontal axis on a coordinate plane is called the _____________-axis

A: Define the coordinate plane.

Q: A full journal bearing with 140 mm diameter and 70 mm length supports a radial load of W. For a…

A:

Q: lows over a flat plat with a velocity of 60 m/s. Calculate boundary-layer thickness at a ce 15 cm…

A:

Q: Figure Txy 1 of 1 σx LI

A: Given system,

Q: drawfree hand diagram of three orthographic views of the given diagram in first angle of projection

A: In the first angle projection, the object is placed in the 1st quadrant. The object is positioned at…

Q: A diesel power station has the following data Fuel consumption/day = 1000 kg Units generated/day =…

A: Here,Fuel consumption per day, .Unit generated per day, .Caloric value of fuel , .Alternator…

Q: We begin with Direction A. (a) What is the x coordinate of the vector tail (x₁)? (b) What is the x…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: . Draw it's projections in all possible positio

A: Given: A point is 50 mm from both the reference planes. To determine: Projections in all possible…

Q: Air with the properties below enters a converging duct. Does the flow reach choked conditions? U =…

A: Hi,  As per the rules, we can provide the solution for only first question so please resubmit your…

Q: 4. (a) Find the tension in each cable supporting the 600-N cat burglar in Figure (b) Suppose the…

A: Given data: F=600 Nθ=37° Need to determine the tensions in each cable.

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.