the minimum diameter required for shaft BC. (b) the minimum diameter required for bolt A.

Q: Find the length of a flat spiral spring 25 mm wide by 0.5 mm thick to store 8 N.m of energy for a…

A: For a limiting stress of 800 MPa, we need to determine the length of a flat spiral spring 25 mm wide…

Q: A fixed bar is pinned at one end and supported by two close helical springs from identical material…

A: Given Data:-       ∗turns:  n=20∗ d=10mm.∗D=150mm       To find out ∗ Max  shear stress in springs…

Q: owing comp ollow shaft C ed torque of

A:

Q: A horizontal shaft of 75 mm in diameter and 350 mm in length projects from a bearing as shown in…

A:

Q: The figure Q3 below shows a bolt holding together two components. The bolt has a load bearing…

A: Thickness of component 1, t1 = 5 mm Thickness of component 2, t2 = 10 mm Modulus of elasticity of…

Q: A fixed bar pinned at one end and supported by two close helical springs from identical material as…

A: Given Datadc=150mmRc=75mmW=10kg=9.81×10=98.1Nd=10mm Ist we have to calculate the force by using…

Q: 1. Question Figure 1.1 shows a crank, OA = 72 mm long which rotates anticlockwise about O at w - rev…

A:

Q: Figure Q2 shows the arrangement of the compressor, turbine and generator in a thermal power plant.…

A:

Q: A square end compression helical spring has an operation load range of 3.5KN to 4.2KN.The deflection…

A:

Q: In the arrangement shown in the figure, a cable is attached to the end of a cantilever beam. We will…

A:

Q: A helical extension spring is made of 1/8-in music wire A228 (E 28.5 Mps G = 11.75 Mpsi, Sut = 271…

A: To calculate the maximum load the spring can withstand, we must calculate the maximum shear stress…

Q: (a) Draw neat illustrative sketches to bring about the difference between a helical coil tension…

A: helical coil compression spring Springs are the energy storage devices that are used to store…

Q: A shaft with a diameter of 51 mm rotates at 1,225 RPM. Three discs are mounted on the shaft, with…

A: Given  , Diameter of the shaft  = 51 mm Speed of the shaft , N =1225 rpm. w1 = 9 N ,w2 = 26 N . w3…

Q: Question 3 AC The circular stepped shaft ABD shown in Figure Q3 has its ends fixed against rotation.…

A: Step 1: Step 2: Step 3: Step 4: solution is given above

Q: The torsional assembly shown in Figure P6.45 consists of solid 2.50 in. diameter aluminum [G=4,000…

A:

Q: A maximum torque of 6.75 kNm can be supplied to the constant diameter steel (G= 80 GPa) line shaft…

A:

Q: t of inertia of the tube, m^4 t of inertia of the solid shaft, m^4 = at D, radians'

A:

Q: 1. Draw the diagram of internal torque applied for each cross-section of the compound shaft  4.2.…

A: As per honor code and answering guidelines I can answer 1st 3 subparts at a time.If you want other…

Q: A rotor having a mass of 5 Kg is mounted midway on a 0.01meter diameter shaft supported at the ends…

A: Calculated dynamic force transmitted to each bearing.

Q: The figure illustrates a stepped torsion-bar spring OA with an actuating cantilever AB. Both parts…

A:

Q: For the column shown in Figure(2), note that the column buckle about its strong axis (x-axis).…

A: To evaluate the given parameters for the buckling of the column, we can use the Euler buckling…

Q: The deflection of the composite spring when subjected to the greatest load A fixed bar is pinned at…

A:

Q: Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered…

A: Given data: Compression helical spring Wmin=416 N Wmax=970 N   Spring index, C = 6.2 Factor of…

Q: (Suuds - pin shorter. The outer s m. Find stiffness of inn

A:

Q: The system below shows a solid shaft composed of 2 circular cross sections (r; = 15 mm, r2 = 30 mm).…

A:

Q: 4- For the shaper mechanism shown in the figure, OA = 50 mm, QB = 350 mm, BC = 170 mm, OQ = 140 mm.…

A: We have to determine displacement slider 6.

Q: i. A shaft system ABCD consists of a solid bar BD and hollow bar AB is subjected to torque as shown…

A:

Q: Q4/A 40 kw power at 300 rpm is transmitted from 50 mm diameter shaft by means of two identical…

A: Given data: Power transmitted by the shaft (P) = 40 kW Speed of the shaft (N) = 300 rpm Diameter of…

Q: We have a line of two equal masses m connected by three springs with spring constants c₁ = 1, c₂= 1,…

A: Given: To find: Stiffness matrix Displacements Limiting values of displacements

Q: A spring made from a wire of 2.5 mm diameter and 750 N/sq. mm. as its working stress Mean diameter…

A:

Q: 12. For the mechanism an figure, degree of shown in figure, degree of freedom is (a) o Marut Tiwari…

A: The links in the given mechanism are shown in the figure below The total number of links is 7 (Link…

Q: The figure illustrates a torsion-bar spring OA having a diameter d = 12 mm. The actuating cantilever…

A: A torsion bar spring OA has a diameter, d=12 mmThe actuating cantilever AB also has a diameter, d=12…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.