A cylindrical bar made of brittle material has been subjected to pure torsion by a torque M and tension from the force F (Figure Q6.c). The torque gives rise to the shear stresses T = T = 32 MPa and the force F gives rise to the tensile stress ху yx 0, = 65 MPa. The stress along the y-axis is zero (o, = 0). Determine whether there will be a failure due to the maximum tensile stress if the tensile strength of the material is 90 MPa.

A cylindrical bar made of brittle material has been subjected to pure torsion by a torque M and tension from the force F (Figure Q6.c). The torque gives rise to the shear stresses T = T = 32 MPa and the force F gives rise to the tensile stress ху yx 0, = 65 MPa. The stress along the y-axis is zero (o, = 0). Determine whether there will be a failure due to the maximum tensile stress if the tensile strength of the material is 90 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q24 Find the stresses in each direction, also find the change in volume of the block of dimension 115 mm x 50 mm x 37 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 22 kN (tensile), 20 kN (compressive), 19 kN (compressive) respectively. Take E as 180 GPa, Poisson's ratio as 0.3
0:07I | ZVAO K/s a 15all KOREK A locs.google.com 11 Q2: The extension spring shown in the figure has full-twisted loop ends. The material is AISI 1040Q&T 400FO wire. The spring has 82 coils and is close- wound with a preload of 18 Ibf. (a) Find the closed length of the spring.(b) Find the torsional stress in the spring corresponding to the preload.(c) Estimate the spring rate.(d) What load would cause permanent deformation?(e) What is the spring deflection corresponding to the load found ?in part d 0.162 in 1 in L-in R -in R. Option 1 O
Q4: Torque wrench in the fig, is made of 350MPA steel and loaded with 1 kN load. Find out the most critical point and the principle stress state at that point? 50 O 25 250 30 25
Q6: A thin steel cylinder 1 m long, of 150 mm internal diameter and plate thickness of 5 mm, is subjected to an internal pressure of 7 MN/m²; the increase in volume due to the pressure is 2.36 x 106 m³. Find the values of Poisson's ratio and the modulus of rigidity. If, in addition to the internal pressure, the cylinder is subjected to a torque of 190 N.m, and axial tensile force at the ends of 650 N, determine the magnitude of the principal stresses set up in the cylinder and their directions. Assume the Elasticity modulus, E = 210 GN/m².
Compare the differences between brittle and ductile materials. Give an example for each material with their corresponding mathematical expressions. A horizontal shaft of 75 mm in diameter and 350 mm in length projects from a bearing as shown in Figure Q4. The vertical load of 10 kN, horizontal compression load of 12 kN and torque, T' Nm are applied at the free end of the shaft. If the safe stress for the material is 145 MPa and assuming the Poisson's ratio is 0.3. Determine the torque, T to which the shaft may be subjected using the following theories: i) The Tresca Theory, and ii) The Von Mises Theory 10 kN Bearing ·· 350 mm Figure Q4 12 kN
A 120 mm ×100 mm ×20 mm T section is used as a simply supported beam. The beam carries the applied eccentric load F of 120 KN at the position indicated in the Figure Q5. Start your calculations be setting an origin from the right most point on the cross section and determine the following : 5.1.The maximum compressive and tensile longitudinal direct stresses induced in the column. 5.2. Plot the stress distribution diagram and determine the position of the NA
A close-coil helical spring is to have a stiffness of 1,000 N/m in compression, with a maximum load of 50 N and a maximum shearing stress of 125 N/mm². The solid length of the spring is 50 mm. Find the wire diameter, mean coil radius, and a number of coils. G= 54,000 N/mm². (Assume shear stress is produced only due to the torque produced in the wire due to axial loading).
Define the terms load , stress and strain. Discuss the various types of stresses and strain p 4:19 /
A 50-mm diameter cylinder is made of a brass for which the stress-strain diagram is as shown. The angle of twist is 5° in a length L = 725 mm. The three points on the nonlinear stress-strain diagram used are (0, 0), (0.0015, 55 MPa), and (0.003, 80 MPa). By fitting the polynomial T = A + By + Cy² through these points, the following approximate relation has been obtained. T= 46.7 × 10%y-6.67 × 1012/2 Determine the magnitude Tof torque applied to the shaft using this relation and the two equations given below. Y Ty - ρφ T (MPa) 2π ζ ρ?τὰρ 100 80 60 40 20 0 0.001 0.002 0.003 Y d = 50 mm L The magnitude T of torque applied to the shaft is kN.m.
The stepped and surface-ground steel bar in the figure is subjected to a bending moment varying between Mz=100 Nm and Mz=250 Nm and a torsional moment varying between Tx=80 Nm and Tx=320 Nm in opposite directions. The tensile strength of the rod material is Sut=800 MPa and it works under room conditions. For 50 percent reliability, check the fatigue safety of the rod.
2. The tapered cylindrical bar in Fig. 2 is subjected to opposing torques T on its free ends. For the tapered section only, the angle of twist 0 can be expressed as: 32 TI(d? + d,d2 + dž) Gd d? 37n (a) Derive an expression for the effective spring constant keff for the entire bar, treating each segment as a torsional spring in series. Fig. 2 (b) For the bar shown, let; I, = 12 = 12 in., 1= 24 in., d1= 0.25 in., d2= 1 in., T = 1000 lbf-in., and G = 13.5 x 103 kpsi. Calculate the angle twist 0 for the entire bar using the expression for kef determined in (a). Verify that this value is the sum the angles of twist for each individual %3D %3D segment.
answer as soon as soon as possible