steps on how to reach answer of 0.188 kg/s The mass flow rate of air at 20°C (p= 1.204 kg/m³) through a 18 cm diameter duct ismeasured with a Venturi meter equipped with a water manometer. The Venturi neck has adiameter of 5 cm, and the manometer has a maximum differential height of 40 cm. Takingthe discharge coefficient to be 0.98, determine the maximum mass flow rate of air thisVenturi meter/manometer can measure. Answer: 0.188 kg/s18 cmh5 cmWatermanometer

Answered: Image /qna-images/answer/5148b5a3-169e-4bae-b668-8797b32766cd.jpg

Answered: The mass flow rate of air at 20°C (p=…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(a) A venturi meter is placed in a pipe to measure the flow of oil with a specific gravity (SG) of 0.9 in a pipe. The inlet has a diameter of 15 cm while the throat diameter is 10 cm. A minimum flowrate of 4.5 L s has to be achieved for the manufacturing of a sauce in one of its processes. Given that the reading on the mercury (SG-13.6) manometer, hm is 20 cm, determine if the flowrate is sufficient for the process. X hm X
The tank below is cylindrical and has a vertical axis. Its horizontal cross-sectional area is 10 m2. The tank has a layer of water under a layer of gasoline (S.G= 0.72). Three holes were drilled in the tank, one at the bottom of the tank, the second hole is in the water layer, 2 m from the bottom. The third hole was drilled 1S 11 in the gasoline layer 5 m from the bottom. The initial discharge velocities from the bottom and the third holes were also recorded as shown in the table below.
A fan is installed in a residential building to provide proper ventilation. This fan isconnected to a duct with 11.6 cm diameter and provides the average air velocity of 5m/s. By regulation, the minimum fresh air requirement is specified to be 0.35 airchanges per hour (ACH) which means 35% of the entire air contained in a room shouldbe replaced by fresh outdoor air every hour. Determine the flow capacity of the fan in litres/min and what the height of the residential building should be.
I need the answer as soon as possible
Water flows in a 15-cm-diameter pipe at a velocity of 1.8 m/s. If the head loss along the pipe is estimated to be 19 m, the required pumping power (in kW) to overcome this head loss is ?"
The air velocity in the duct of a heating system is to be measured by a Pitot-static probe inserted into the duct parallel to flow. If the differential height between the water columns connected to the two outlets of the probe is 2.4 cm, determine the flow velocity at the center of the duct in m/s. R of air is 287 J/Kg-K.
The volume flow rate of liquid refrigerant-134a at 10°F (? = 83.31 lbm/ft3) is to be measured with a horizontal Venturi meter with a diameter of 6 in at the inlet and 2 in at the throat. If a differential pressure meter indicates a pressure drop of 7.5 psi, determine the flow rate of the refrigerant. Take the discharge coefficient of the Venturi meter to be 0.98.
Knowing the density, and the volumetric flow rate, omdot P the mass flow rate, mdot can be calculate using the equation o mdot om dot d P² 2 & la 0² 2 PD²
Air flow through the pipe at a rate of 170 L/s. The pipe diameter ismeasured to be 20 cm at the entrance, which reduces to half with asmooth reducing section. The pressure difference between the two pipesections is measured by a water manometer. Assume the systemoperates in the environment at a constant temperature 50°C. Determine the differential height of the water in the manometer and list 3 assumptions that you made.
Oil with density 905 kg/m^3 and viscosity 2.33 kg/m.s flows in a 430 meter long 42-cm-diameter horizontal pipeline at an average velocity of 0.7 m/s. Determine the pumping power required in kW to overcome the pressure losses and to maintain the flow of oil in the pipe. Make sure to check Reynolds number first to identify the type of flow and use the proper equation.
Is the assumption in this question (for ther manometer part) that water is used as the other lquid in the mercury manometer? Can any other fluid be used? You do not have to solve the equation* Thank you
Kindly solve this problem with complete solution so that I can Understand. Correct Final answer: 60.59 %

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS