27.The left ventricle of a resting adult's heart pumps blood at a flow rate of 83.0 cm³/s,increasing its pressure by 110 mm Hg, its speed from zero to 30.0 cm/s, and its heightby 5.00 cm. (A/l numbers are averaged over the entire heartbeat.) Calculate the totalpower output of the left ventricle. Note that most of the power is used to increaseblood pressure.

Given:Pressure,P=110mm of Hg=(110×33.32)Nm2=14665.2Nm2Density of blood,ρ=1.05×103Kgm3Velocity of…

The left ventricle of a resting adult's heart pumps blood at a flow rate of 83.0 cm³/s, increasing its pressure by 110 mm Hg, its speed from zero to 30.0 cm/s, and its height by 5.00 cm. (All numbers are averaged over the entire heartbeat.) Calculate the total power output of the left ventricle. Note that most of the power is used to increase blood pressure. 27.

The left ventricle of a resting adult's heart pumps blood at a flow rate of 83.0 cm³/s, increasing its pressure by 110 mm Hg, its speed from zero to 30.0 cm/s, and its height by 5.00 cm. (All numbers are averaged over the entire heartbeat.) Calculate the total power output of the left ventricle. Note that most of the power is used to increase blood pressure. 27.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A and B are homologous pumps operating at the speed of 800rpm.Pump A has an impeller with diameter 60 cm and discharges 1.5m^3/s of water under a net head of 60m.Calculate the size of pump B, net head and the specific speed to discharge 0.9m^3/s.
Two pumps (Pump A and B) have performance curves which can be approximated by the following equations: H_A = 340 - (1.2(Q^2)), in feet H_B = 360 - (2.5(Q^2)), in feet where Q is in ft^3/s. If pumps A and B were to operate in parallel as depicted in the figure below, at what head (in ft.) should either pump be operated?
1. A Pelton wheel performance data are collected in the following table. Turbine speed (RPM) 3000 Shaft torque Water supply line pressure (bar) Water flow rate (L/min) (Ncm) 2.4 18.4 If water supply pipe diameter is 25 mm and turbine wheel diameter is 70 mm, calculate the hydraulic head in m, jet velocity in m/s, speed ratio, hydraulic power in W, mechanical power in W and efficiency of the turbine. What is the optimum speed (RPM) of the wheel (for maximum power)?
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. A. 12.74m B. -4.67 m C. -2.72 m D. 2.56
Need detailed solution. 4 decimal places. A fluid is flowing in a 6 in diameter pipe at a pressure of 4 psi with a velocity of 8 ft/s. The elevation of the center of the pipe above a given datum is 10 ft. Find the total energy head above the given datum in meters if the fluid is (a) water, (b) oil with specific gravity of 0.85, (c) gas with specific weight of 0.42 lb/ft^3
Experiment Data Take the following data for the syringe injection pump 2/ Inner diameter of syringe barrel: D = 1.5 cm Inner diameter of the needle shaft of the syringe: d = 0.5 mm The thread pitch of lead screw: pt = 0.75 mm Lead screw rotation velocity (rpm): n Calculations Liquid injection rate (cm³/hr) Q = pt*n* 60 * * D²/4 Velocity of liquid in syringe barrel (cm/min) v = 4Q/ (60** D²) Velocity of liquid in syringe needle (cm/min) v₁ = 40/ (60* *d²) K Find the rotation velocity of lead screw n and the velocity of liquid in syringe needle if the required injection dose is 1. 10 cm³ in 3 hours (continuous injection) 2. 20 cm³ in 12 hours (discontinuous injection, 5 cm³ each 3 hour, injection time = 1 min). Discus the rece Solution Calculate the liquid injection rate Q = P₁ xnx60x² = 0.075xnx60xx1.5 = 7.94n- cm³ hr Calculate the velocity of liquid in barrel V₁ == 40 60xπx D² 4x7.94n 60xx1.5² = 0.07ncm hr Calculate the velocity of liquid in needle 40 60xπxd² 4x7.94n 60xπx 0.05² hr…
In the pumping system shown below, determine the following. a. Head loss at suction in m b. Head loss at discharge in meters c. Total head losses in meters d. Total dynamic head developed by the pump in meters e. Water Power in KW f. Brake Power in KW g. Energy consumption for 15 hours operation in KW-hr h. Line current drawn by the 3-Phase motor drive in amperes i. Pumping cost in Pesos/Day if electricity costs P7.00/KW-hr Figure: Other Data Water Temperature: 20∘C Suction Line 5−20 m 1−90∘ Elbow 1− Check Valve (Fully Open) Pipe Material: Galvanized Iron ND=100 mm Discharge Line L=50 m 12−90∘ Elbow 1− Gate Valve (Fully Open) 1− Check Valve Pipe Material: Galvanized Iron ND =80 mm Pump Efficiency: 75% Motor Efficiency: 82% Volts: 220 V Power Factor: 92%
A pump with an impeller diameter of 300 mm running at a speed of 2950 rev/min delivering 450 L/min of water at a head of 350 kPa is going to be replaced by a geometrically similar spare pump running at a speed of 1450 rev/min delivering the same flow rate and head. Determine the impeller size of the spare pump and the percentage increase (decrease) of power required for the spare pump. OL. 380.1 mm; a decrease of 61.33% OI., 380.1 mm; an increase of 38.77% I. 147.5 mm; an increase of 3.4% IV. 210.3 mm; a decrease of 83.1%
Two pumps (Pump A and B) have performance curves which can be approximated by the following equations: H_A = 340- (1.2(Q^2)), in feet H_B = 360 - (2.5(Q^2)), in feet where Q is in ft^3/s. If pumps A and B were to operate in parallel as depicted in the figure below, at what head (in ft.) should either pump be operated? ... Pump A Round your answer to 2 decimal places. J Pump B
The characteristics of a particular pump are shown in the image below. Calculate the head and discharge one would get at maximum efficiency if the size was doubled and the speed was halved.
Complete Solution please, thanks. 3. A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5 m at the top. Gas with a unit weight of 0.12 N per cubic meter enters the bottom of the tank with a uniform velocity of-assume values with decimals between 3 to 4 m per second- enters the stack. The unit weight increases by 7.5 percent every 2 meters. Find the velocity of flow at every 5 meters along the stack.
The pressure differential of oil (with specific gravity of 0.789) flowing through different sections of pipe is 750 Pascals. If the velocity of the oil in the first pipeline section is 1.2 meters per second what is the velocity of this oil in the second pipeline section?