The landing gear of a light airplane is displayed by the figure. What is the compressive stress in strut AB caused by the landing reaction R = 57 kN? Neglect the weights of the members. The strut is a hollow tube, with 69-mm outer diameter and 43-mm inner diameter. 400 600- Dimensions in mm

The landing gear of a light airplane is displayed by the figure. What is the compressive stress in strut AB caused by the landing reaction R = 57 kN? Neglect the weights of the members. The strut is a hollow tube, with 69-mm outer diameter and 43-mm inner diameter. 400 600- Dimensions in mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.6P: Consider the plane truss with a pin support at joint 3 and a crtica1 roller support at joint 5 (see...

See similar textbooks

Similar questions

Solve the preceding problem if the mass of the tailgate is MT— 11 kg and that of the crate is hic— 6S kg. Use dimensions H = 305 mm, L = 406 mm, dc= 460 mm, and dT= 350 mm. The cable cross-sectional area is At= 11.0 mm'. (a) Find the tensile Force T and normal stress T in each cable. (b) IF each cable elongates
Determine the weight “W” of the heaviest cylinder that can be supported in the position as shown in the figure. Allowable stress for the cable is 40 MPa. Neglect any frictional resistance. Assume that the cross-sectional area of cable BC is 120 mm2. Also, calculate the reaction between the uniform cylinder and the vertical wall.
Clamps like the one shown are commonly used in woodworking applications. This clamp has the dimensions given in the table below the figure, and its jaws aret = 49 mm thick (in the direction perpendicular to the plane of the picture). a.) The screws of the clamp are adjusted so that there is a uniform pressure of P = 115 kPa being applied to the workpieces by the jaws. Determine the force carried in each screw. Hint: the uniform pressure can be modeled in 2-D as a uniform distributed load with intensity w = Pt (units of N/m) acting over the length of contact between the jaw and the workpiece. b.) Determine the minimum vertical force (parallel to the jaws) required to pull either one of the workpieces out of the clamp jaws. Use a coefficient of static friction between all contacting surfaces of us = 0.4 and the same clamping pressure given for part (a). 2013 Michael Swanbom BY NC SA d 0000 O bo 0000000 P b. Values for dimensions on the figure are given in the following table. Note the…
7. In the wedge shown in the figure. Determine the largest angle that will cause the wedge to be self locking whatever the value of force P may be. Neglect the weight of the wedge. Hg = 0.3 P 0 P
Determine the force in members BC, GA, and BG of the truss shown in the figure below. Let P = 175 kN. NOTE: If your answer is a compressive force then just put a negative sign. If your answer is a tensile force then just type the answer directly. (ALSO, DON'T FORGET THE UNITS) 2P 2P 30 60V60° B 60 60° 30 3P 4m 4m 4m Solve the force in member BC. Solve the force in member GA. Solve the force in member BG.
Two wooden members are glued together as shown in the figure. Each member has a width of b = 1.25 in. and a depth of d = 3.45 in. Use ß = 82 °. Determine the average shear stress magnitude in the glue joint if P = 1080 lb. Part 1 Use the notion of symmetry and construct an FBD for only the upper half of the left-hand wood piece. What is the magnitude of the portion of Load P acting on this upper half? Pupper = eTextbook and Media Save for Later Part 2 V = Based on the FBD for the upper half of the left-hand wood piece, determine the shear force in the glue joint. eTextbook and Media Save for Later Part 3 lb lb A₁ = Determine the area of the upper half of the glue joint. in.² Attempts: 0 of 5 used Submit Answer Attempts: 0 of 5 used Submit Answer
The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap D= 4 mm between the lower end of the left rod and its pin support at C. Compute the stress in the left rod after its lower end is attached to the support. The cross-sectional areas are 300 mm2 for rod AC and 250 mm2 for rod BD. Use E= 200 GPa for steel. lo/0 0.75 m 1.5m 2 m ANSWER: MPa
I am struggling with this question
The dimensions of the block given the loading condition are a = 40, b = 30 and c = 6 mm. Calculate the maximum load p that can be applied without creating stress in the x direction and the extension rates in other directions at this moment.(Modulus of elasticity: 200Gpa, Poisson's ratio: 0.3)
The compound bar is supported by a journal bearing at point E, a thrust bearing at point F and a cable connected between points A and B. The bar is subjected to a point load at point C and a couple moment at point D, as shown in the figure. Determine the support reactions and the force in the cable. Note that the bearings are proper alignment and that point A lies on the xz plane, while point B is on the xy plane. A Free Body Diagram (FBD) is required to receive full points. Neglect the weight of the bar. M=500 lb-ft E A 3 ft B 5 ft D F 2 ft 4 ft C P= 1,000lb \ 3 ft y B
In the figure, torsional moments act on a bar system of abruptly changing cross-section made of the same material. Accordingly, calculate the value of the factor α so that the support responses are of the same magnitude in absolute value. What must the torsional moment=Mb be for the D-end to be zero? Note: The shear modulus of the material is G = 80 GPa Mo= 10 kNm.
Three solid bars, each with square cross sections, make up the axial assembly shown. Two loads of P = 31 kN are applied to the assembly at flange B, two loads of Q = 21 kN are applied at C, and one load of R = 53 kN is applied at end D. Bar (1) has a width of b1 = 100 mm. Calculate the width b2 required for bar (2) if the normal stress magnitude in bar (2) must equal the normal stress magnitude in bar (1).