The internal shear force V at a certain section of an aluminum beam is 6.9 kN. If the beam has the cross section shown (assume a=29 mm, b-72 mm, tw-t-5 mm, d=82 mm), determine: (a) the shear stress that point H, which is located 29 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress Tmax in the tee shape. bf MPa. H a Answers: (a)th = (b) Tmax kw i i MPa.

The internal shear force V at a certain section of an aluminum beam is 6.9 kN. If the beam has the cross section shown (assume a=29 mm, b-72 mm, tw-t-5 mm, d=82 mm), determine: (a) the shear stress that point H, which is located 29 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress Tmax in the tee shape. bf MPa. H a Answers: (a)th = (b) Tmax kw i i MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

As3
For the beam showna. Determine the maximum flexural stressb. If the nails shown in the cross-section can each support a shear force of 600 N,determine their required spacing along the beam. P=10kN Wo=8kN/m a=10m
3
X Incorrect Three plates are welded together to form the section shown. Dimensions of the cross section are b = 3.6 in., d = 10.8 in., a = 2.3 in., and t= 0.4 in. For a vertical shear force of V = 39 kips, determine the shear flow through the welded surface at B. d В Answer: i 1.283 kip/in.
A 62-kN vertical load P is applied at the corner of the square cross section of the steel compression member AB, which is free at its top A and fixed at its base B. Knowing that for the grade of steel used Øy=345 MPa and E= 200 GPa, and using the allowable-stress method, determine the smallest allowable dimension d. 1.5 m The smallest allowable dimension dis mm.
1. For the W 21x 62 steel beam below determine the actual value of om in the beam and the maximum value of the principal stress omax at the junction of the flange and the web. 20 kips 20 kips A B 10 ft 2 kips/ft 30 ft- C 10 ft D
Three plates are welded together to form the section shown. Dimensions of the cross section are b = 4.7 in., d = 14.1 in., a = 3.7 in., and t= 0.8 in. For a vertical shear force of V = 46 kips, determine the shear flow through the welded surface at B. d В b. Answer: kip/in.
STRENGTH OF MATERIALS The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure stress for steel is 360MPa, determine the minimum thickness t of the pipe if it supports the force of 600KN. Use a factor of safety against failure of 1.50. Also, find the minimum radius r of the base plate so that the minimum factor of safety against failure of the concrete due to bearing is 2.50. The failure bearing stress for concrete is 28MPa.
Complete answer
An extruded aluminum beam has the cross section shown. Knowing that the vertical shear in the beam is 10 kips, determine the shearing stress at (a) point a, (b) point b. 2.4 in. 0.5 in. 0.25 in. 0.25 in. 4 in. a -0.5 in. t 1.2 in. 4
The internal shear force V at a certain section of an aluminum beam is 10.2 kN. If the beam has the cross section shown: a = 30mm, bf = 69mm, tw = tf = 4mm, d=72 mm, determine:(a) the shear stress Th at point H, which is located 30 mm above the bottom surface of the tee shape(b) the maximum horizontal shear stress Tmax in the tee shape
Part 2,3,4