A 62-kN vertical load P is applied at the corner of the square cross section of the steel compression member AB, which is free at its top A and fixed at its base B. Knowing that for the grade of steel used Øy=345 MPa and E= 200 GPa, and using the allowable-stress method, determine the smallest allowable dimension d. 1.5 m The smallest allowable dimension dis mm.

A 62-kN vertical load P is applied at the corner of the square cross section of the steel compression member AB, which is free at its top A and fixed at its base B. Knowing that for the grade of steel used Øy=345 MPa and E= 200 GPa, and using the allowable-stress method, determine the smallest allowable dimension d. 1.5 m The smallest allowable dimension dis mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Part 2,3,4
A 200 MPa shear stress is applied on along CD. Calculate diagonal strain along AC. Given modulus of elasticity is 120 GPa and Poisson's ratio is 0.2. 200 MPa A B Diagonal strain will be in the form of k x 10-3 Find 'k'
Question
5. If exactly 20 bolts of 2.5cm diameter are needed to hold an air chamber together at A-A as a result of the high pressure within, how many bolts will be needed at B-B ? Here D=40cm and d=20cm. B
A composite beam is made of two brass [E = 97 GPa] plates bonded to an aluminum [E = 72 GPa] bar, as shown. The beam is subjected to a bending moment of 2420 N-m acting about the z axis. Assume b=64 mm, d1=36 mm, d2=13 mm. Determine: (a) the maximum bending stresses opy,Gal in the brass plates and the aluminum bar. (b) the stress in the brass obrj at the joints where the two materials are bonded together. Brass (2) d2 Aluminum (1) Brass (2) dz b Answers: (a) obr = i MPa, oal = i MPа. (b) Obrj MPa.
During the tension test, the wooden specimen is subjected to an average normal stress of 2 ksi. Determine the axial force P applied to the specimen. Also, find the average shear stress developed along the section Ɵ -a of the specimen.
QU A composite beam is fabricated by bonding a steel bar and a brass bar and is subjected to the bending moment M = 200 N-m. Determine the maximum bending stress in the brass and steel. Given: E, =200 GPa, E, = 100 GPa Brass 20 }o | Jakrtal
3. Determine the stress in each of the two vertical rods if the temperature rises 50 °C after the load P=75 KN is applied. Neglect the deformation and mass of the horizontal bar AB. Use Ea = 75 GPa, as=23.0 um/m-°C, Aa = 850 mm2 Es = 210 GPa, as = 11.9 um/m-°C and As = 650 mm² . %3D %3D Steel Aluminum 3m 2.5m 3 m 3 m 3 m 75 KN
Question 3 of 5 -/ 20 E View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b 2.4 m, and c = 5.2 m. %3! C (1) a Answer: kN P = Attempts: 0 of 1 used Sub Save for Later B.
SITUATION. Determine the value of 0 if the shearing stress on the glued joint is thrice that of the normal stress.
Determine (d) variable stress and (e) design factor
SIR, PLS GIVE ME PROPER AND CORRECT SOLUTION WITH DETAIL. THANKS