The inside diameter of a sampler tube is 50 mm. The inside diameter of the cutting edge is kept such that the Inside Clearance Ratio (ICR) is 1.0% to minimize the friction on the sample as the sampler tube enters into the soil. The inside diameter (in mm) of the cutting edge is (round off to two decimal places)

The inside diameter of a sampler tube is 50 mm. The inside diameter of the cutting edge is kept such that the Inside Clearance Ratio (ICR) is 1.0% to minimize the friction on the sample as the sampler tube enters into the soil. The inside diameter (in mm) of the cutting edge is (round off to two decimal places)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Can be made up
Pls fast hand written solution
4. A series of tests are run on a HMAC Sample. The following data is given to you:% AC (Pb) = 10 %Gb = 1.040Gsb = 2.51Gmm = 2.696Mass of compacted HMAC sample = 840 grMass of compacted HMAC sample submerged in water = 512 grMass of compacted HMAC sample, SSD condition = 847 gra. Based on the above information what is the Gmb? b. Based on the above information what is the of VTM? c. Based on the above information what is the of VMA? d. Based on the above information what is the of VFA?
Sample 2: Mass with empty mold M1 Mass of soil and mold M2 Hydraulic Head h Time interval t Volume V 145 g 250 g 950 mm 0.34 min 0.0046 L 145 g 260 g 900 mm 0.33 min 0.0049 L 145 g 228 g 922 mm 0.30 min 0.0051 L 145 g 281 g 915 mm 0.29 min 0.0044 L 145 g 219 g 908 mm 0.39 min 0.0042 L The diameter of the mold = 2.5 cm, Length of the sample = 0.3 m can u pls Find the permeability coefficient Mass of the soil Bulk Density Dry Density thank you Void Ratio
In a liquid limit test using Fall cone apparatus, the following readings were recorded. While in the plastic limit test, the following data were obtained: Weight of soil + container = 22.12 grams Weight of dry soil + container = 20.42 grams Weight of container = 13.07 grams Determine the ff. (SHOW COMPLETE SOLUTION AND GRAPH) A. Find the liquid limit B. Compute the plastic limit. C. Find the liquid limit. D. Find the plastic limit. 40% 45% 50% 58% Water Content 12 16 21 35 Penetration of cone(mm) -PLS SHOW COMPLETE SOLUTION AND GRAPH. SHOW YOUR ANSWER IN 4 DECIMAL PLACES. I'LL RATE, THANKS!
Standard Test Method For Penetration of Bituminous test 1. Importance of penetration test.2. Effect of temperature, load and time on penetration values. State otherconditions.3. The use of different grade in different climates.4. What is the meaning of “consistency of bituminous materials”?5. Which value of penetration can be used in construction of roads in Iraq?
Q.2) Answer the following question. 1- The sieve analysis below was done for which type Weight of sample = 2000gm Sieve size in. (mm) 3/8" 9.5 mm No.4 4.75 mm No.8 2.36 mm No.16 1.18 mm No.30 0.6 mm No.50 0.3 mm No.100 0.15 mm Pan Percent Weight retained (g) retained 0 2000*100 94 →0 Klcc→ -2000 4032000X100 358-2009 08 72 2212000x100 Percent cumulative @ 4.7 20 i 75 982 57 360 72000 Alco isies 39 492-20000 24.614 · 100 > 95 3 of aggregate. Percent passing 0 5 25 уз 61 86 97 317 ASTM Limit 100 95_100 80_100 40 85 25_60 10_30 2_10
27
The Professor demonstrated the proper application of the procedure by analyzing a 50 mL sample of water from a local lake (Rivers Parkway) via titration with a standard solution of EDTA 0.0100 +0.0001 M standard. This sample consumed 5.00 mL to reach the Total Hardness (TH) end point; therefore, the TH of the lake was determined to be XX ± YY mg/L as CaCO,.
In Triaxial test, which of the following parameters do not need to be recorded the confining pressure specimen diameter changes the generated pore pressure the axial force