The force from the cable AB attached to the screw eye at A is F = {500 - i – 100 · ĵ – 300 - kN. If the length of the cable is L = 10 m, then what are the values for x, y, and z?

Q: Determine the magnitudes of all pin reactions for the frame loaded as shown. 785 mm 27° 315 mm B 61°…

A:

Q: A 10 unit force acts at point Q shown on the Q4 element shown below. Determine the load vector of…

A:

Q: *2-4. The vertical force F acts downward at A on the two- membered frame. Determine the magnitudes…

A:

Q: The line of action of the 3250-lb force runs through the points A and B as shown in the figure…

A: Detailed explanation and solution of the above problem uploaded in below picture.

Q: If 8 = 30° and T = 6 KN, determine the magnitude of the resultant ford acting on the eye bolt * 45

A: Given   Force, F = 8 kN             T = 6 kN Find   Resultant force, R

Q: 5. The crowbar is subjected to a vertical force P = 110 N at the grip, whereas it takes a force of F…

A: The crowbar is subjected to a vertical force P = 110 N at the grip, whereas it takes a force of F =…

Q: 2-90. The 8-m-long cable is anchored to the ground at A. If z = 4 m and y = 2 m, determine the…

A: Answer 2-90: Given data: L=8 mx=4 my=2 m Need to determine the coordinate z to the highest point if…

Q: Figure (1) B(170N) 7(14,8,-4) 6 4 12 y A

A: Given force F=170N actsalong line AB, where B=(14,8,−4)the coordinates of A can be foundby given…

Q: 1. The tower is held in place by three cables. If the force of each cable acting on the tower is…

A:

Q: Determine the required magnitude of F1, F2, and F3 so that the resultant couple moment is

A: Moment:- Moment of any force is the measure of its tendency to rotate a body about its axis. It is…

Q: e loading by an equivalent resultant force and couple moment at point. Suppose {8i - 2k) kN and F₂ =…

A:

Q: Figure 1 shows a door of size 1200 mm by 400 mm supported by hinges at an inclined axis. E is at the…

A:

Q: Practice Problem#2: 2-71. If a = 120°, ß < 90°, y = 60°, and F = 400 lb, determine the magnitude and…

A:

Q: Draw the correct Free Body Diagram (FBD). Solve the force T and θ if the Resultant of 500N is…

A:

Q: Find the moment of the force about C.

A: Given data, The coordinates of C = (6, 0, -6) The coordinates of E = (13.5, 8, 0) Force P, P→ =…

Q: What is magnitude of the moment about the O-A axis produced by the applied force at C given that the…

A: According to the given dataA=(0.3 , 0.4 , 0)  mO=(0 , 0 , 0)  mC=(0.1 , 0.4 , 0.3)  m   NWe need to…

Q: The horizontal force P is subjected on the slit open circular ring beam. Determine the horizontal…

A: Horizontal displacement at point A: - Assume any section x-x and point x on the ring. Now moment at…

Q: Please give a detailed solution. Follow the sign convention given in the problem, Draw complete Free…

A:

Q: F M F= {30 i+ 40j + 50 k} N applied to point M| strength; 3 N (a) The moment it develops around O…

A:

Q: 4-143. If F₁ = 7 kN and FB = 5 kN, represent the force system by a resultant force, and specify its…

A: Given that: FA = 7 kN FB = 5 kN It is required to determine the value of the resultant force and the…

Q: Choose the correct answer for five points only ) The tension Tin the cable AB is maintained at a…

A:

Q: Example: Replace the three forces acting on the bent beam by a single force R. Specify the distance…

A:

Q: Determine the reactive forces and moments at the point O and point A 6 kN/m 15 kN 500 kN m 7.5 m 4.5…

A:

Q: Determine both the X and Y components of the 300 N force shown in the figure below. (-7,37) +y 300 N…

A: According to the given data There are two point  A=(-7,37) B=(45,-3) Force 300N is form A to B We…

Q: In the figure, cables AD, AB and AC are needed to support the 60lb box. Determine the coordinates of…

A:

Q: Determine the value of A so that A = 2i + ah + k and B = 4i - 2j - k are perpendicular.

A: To find ; The value of a so that A is perpendicular to B . Given: The vectors are A=2i+aj+k and…

Q: X 4 ft 3 ft N F = {30i - 45j + 50k} lb C 0 4 ft B 4 ft 2 ft

A: Given:The diagram for the problem is given below;

Q: 6. Determine the tension in each segment of the cable and the cable's total le 4 ft 7 ft B

A: Find     FAB , FBC, FCD, and total length

Q: The total torque of the forces on the ruler around a axis perpendicular to the ruler and passing…

A:

Q: Determine the magnitude of the moment of the force F={50i− 24 j − 80k}N about the base line CA of…

A: objective is to determine the magnitude of moment of force F about base line CA

Q: AF = 2 kN force is applied on steel pipes in -z axis direction. According to connection coordinates…

A:

Q: D a N F₁ a B L2 L₁ F2 N F3 A -X

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Two cables connect anchors-one from A to B and one from A to C. Cable AC creates a 100 lb force F at…

A: Given Data: The coordinate of point A is (0,0,7). The coordinate of point B is (10,0,0). The force…

Q: y F1 d1 d1 F2 F3 dz F4 F1 = 59 N F2 = 68 N F3 = 40 N F4 = 44 N d, = 3 m

A:

Q: Determine the magnitude of the moment of the force F={300i-200j+150k} N about the DB axis.

A:

Q: *2-12. Determine the design angle (0° s ¢ s 90°) between struts AB and AC so that the 800-N…

A: The free body diagram of above members as follows: Find the force in Ac member from the Cos rule as…

Q: The bar shown in the following figure is subject to a force of intensity of 60N in the sense of C to…

A:

Q: 5) Use the method of sections to find the true magnitude and direction in bar DB of the truss. Hint(…

A:

Q: Determine the magnitude and direction of 0 of F_1 so that the resulting force is directed along the…

A: Determine the magnitude and direction of thita (@) of F1 so that the resulting force is directed…

Q: Q1\ The 50-N force P is applied perpendicular to the portion BC of the bent bar. Determine the…

A: Moment of P about the point B is MB=P×BC=50×2=100 N·m

Q: If the magnitude of F2 were increased by 1/3, what is the resultant moment at A? Round your numbers…

A: The force vector are The magnitude of F2 is increased by .

Q: 5. Determine the principal stresses acting at point E by constructing Mohr's circle y. 150 mm 200 mm…

A:

Q: y y Y O SA 20 Cathy Zupke The value of z = m The value of y = The value of

A: For solution refer below images.

Q: The post are subjected by three cables as shown in Figure 1. The resultant forces, FR of the three…

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.