The horizontal force P is subjected on the slit open circular ring beam. Determine the horizontal and vertical displacements at point A.

Q: Find the magnitude of the moment of force F about point A, given:    F̄ =  lbs,   LX = 6 ft,   LY =…

A:

Q: In the system shown in the figure, TBA = (202) kN. and TCA = (501) kN. is, find the moments of these…

A:

Q: The figure shows a control bar, subjected to a force of 90N. Since the length of the bar is 225 mm…

A: GivenF=90NL=225mm=0.225mMB=13.5 Nm clockwiseα=?

Q: Two forces L (parallel to the y-axis) and A (parallel to the z-axis) are applied at point Q on the…

A:

Q: 3/ calculate the moment of the 60N force about point O for the condition 0 30

A: The moment of a force is the product of the force with the perpendicular distance from the point of…

Q: Problem 3 w2 kN/m 7x kN/m From the figure, w1=11kN/m, w2=15KN/m w1 kN/m 1. Find the resultant of the…

A:

Q: Problem 1: From the figure, F1 =22KN, F2 =27KN 1. Find the resultant of the forces 2. Find the…

A: Consider the diagram as shown below for the given system.

Q: Determine the moment produced by force Fabout segment AB of the pipe assembly. Express the result as…

A:

Q: HOME WORK 3 Determine the resultant force at A. for the figure below Hint : 1- Find the position of…

A:

Q: Find the x-component the resultant of two forces: A= 100N, acting 30 degrees to left of the negative…

A:

Q: Two different ropes connected to the A ring, FB and FC as in the figure. pulling forces are applied.…

A: A position vector for a line representing with two end points can be obtained by subtracting the…

Q: Situation 1- For the forces shown in the Figure AP-4.1: 1. Determine the X-component of the…

A:

Q: Problem 4 From the figure, w1 =13kN/m, w2=10kN/m, F1 =7kN 1. Find the resultant of the forces 2.…

A: Given w1 = 13 KN/m w2 = 10KN/m F1= 7 KN

Q: An engineer is using the pliers shown below to twist a pin at P. Based on the parameters given, find…

A: Moment is defined as the product of force and the perpendicular displacement.

Q: Solve for the resultant forces and moments at points A and B in the diagram below [Figure 2] [20…

A: A beam when subjected to load tends to bend. Resisting forces act at the support. These forces are…

Q: w1 Problem 4 F1 From the figure, w1 =15KN/m, w2=12kN/m, F1 =7kN 1. Find the resultant of the forces…

A:

Q: Q7/ Two integral pulleys are subjected to the belt tensions shown in the figure. If the resultant R…

A:

Q: The forces in the figure are P=80 N, Q=110 N. Find the direction and intensity of the sum of moments…

A: Solution: The coordinate of point A is calculated as: A=(-3-8cos40°,0,-8sin40°)=(-9.13,0,-5.14) The…

Q: Determine the internal forces at point J, with alpha = 0°

A: Introduction: Internal forces: External forces acting on structure elements such as poles, beams,…

Q: The given force in the figure passes through the origin and point A(5,-12,16). Its z-component is

A:

Q: The modulus of force F in the figure is 450 N. Determine the moment of the force with respect to the…

A:

Q: Problem 3 w2 kN/m 7x kN/m From the figure, w1=9kN/m, w2=13KN/m 1. Find the resultant of the forces…

A:

Q: For the force shown in figure, find the resultant (R) by component method

A: Consider the diagram shown below for the given forces.

Q: Using the image below replace the distributed loading with an equivalent resultant force, and…

A: Given data:- L1 = 9 ft W1 = 70 lb/ft W2 = 420 lb/ft To find:- Replace the distributed loading with…

Q: Find the moment of the Force P in the figure relative to the axis AD in terms of unit vectors.

A:

Q: Find the sum of the horizontal forces in Newton if F1 = 100 N at 30 deg N of E and F2 = 80 N at 45…

A: Given Data: Force F1=100 N at 30° North of East. Force F2=80 N at 45° North of West.

Q: Consider the given values for the force system shown:       xA = 9 ft xB = -12 ft xC = 7 ft…

A: Vector A is: Vector B is: Vector C is:

Q: Using the component method, find the complete resultant of the following forces: F= 2m, 40° N of E,…

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.